Replaces

1999-1999 VW Golf 4 Door Power Window Regulator (without Motor) Rear Passenger Side (Built After 10/01/98 Production Date)

Part Details

  • Operation: Power
  • Location: Passenger Side
  • Location: Rear

This part replaces:

  • OE # 1J4839462F
  • HOLLANDER 135-58451R, 135-58455R
  • DORMAN 740-927

  • New

This Volkswagen Golf and Jetta power window regulator is just what you need to get your vehicle in good looking form again!

Specifications:

  • RH (Passenger Side) REAR DOOR
  • Does NOT include the power window motor
  • Replaces dealer part numbers: 1J4-839-462-F, 1J4839462F
  • New, not rebuilt
  • Direct bolt on
  • Built to strict quality control standards
  • Does NOT fit 2 door models

For vehicles needing info with a production date: You can find the production date of your vehicle on either the outer edge of the driver's front door or on the latch piller that the door closes on.

For vehicles needing info with a VIN code: You can find your vehicles VIN (vehicle identification number)in the driver's side lower corner of the windshield near the A pillar, on your title, or on your state registration.

This Volkswagen Golf and Jetta power window regulator makes a great replacement and has good cost savings over a dealer unit.

Installation

  • This repair is easier than you may think. You'll find our installation videos helpful. In our experience removing and replacing the door panel is the most involved step in the repair. On most vehicles this only requires removing a few screws and push in clips.
  • You'll get a great feeling of accomplishment after you complete this repair knowing you saved money, and you didn't have to give up your car for a day at the repair shop. Your passengers and other drivers will be amazed.

Fit guaranteed

  • 1A Auto will refund you with no hassle, if this Window regulator does not fit the application stated.
    • You can use your existing hardware and wiring harnesses. This Regulator will install just as your original does. Save time and money.

Quality

  • Be confident this part will work right. Every regulator is tested after assembly to make sure all mechanisms are working correctly.
  • It is important that your new regulator works for a long period of time. The design of this regulator is tested to withstand 10,000 cycles. That is enough to raise and lower your window 3 times per day for 9 years.
  • Nothing is more frustrating than taking your car apart and finding the part you purchased does not fit. You want the part to fit. This design is test fit on an actual door. When you install it, you will have no issues.

Value

  • Windows that don't work can be frustrating. They can also hurt your vehicles value. An inoperable window could mean $200-$500 discounted off a dealer trade value or asking price.
  • Some shops and dealers charge more for parts and repairs when they think you don't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly repair bill.

 

2 Year Warranty

This item is backed by a 2 Year Warranty. In the event this item should fail during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Door Panel (0:42 in the video)
    • Pry off the door pull cover with a flat blade screwdriver
    • Remove two Phillips head screws from inside the door pull
    • Remove the two T20 Torx bolts from the bottom of the door panel
    • Pry out on the door panel by hand
    • Lift the door panel off of the window sill
    • Disconnect the wiring harnesses from the door panel
    • Pry back the door handle cable clip with a flat blade screwdriver
    • Unhook the door handle cable
  2. Disconnecting the Window Regulator Panel (2:01 in the video)
    • Disconnect the window motor wiring harness with a flat blade screwdriver
    • Disconnect the speaker wiring harness
    • Pull of the lock rod clip
    • Pull the door cable rod off its clips
    • Disconnect the wiring harness from its clip
    • Push in the mounting tabs in the middle of the regulator panel
    • Remove the three T30 Torx bolts from the window motor
    • Pry off the rubber cover
    • Slide the window down by hand
    • Twist a screw into the inner window clamp ring
    • Pull the screw out with a pair of pliers
    • Pry out the outer window clamp ring with a flat blade screwdriver
    • Pull the window up by hand
  3. Removing the Window Regulator (4:08 in the video)
    • Remove the 10mm bolts from the window regulator panel
    • Push in the three mounting clips in the upper right corner of the panel
    • Pull the panel partially out
    • Disconnect the wiring harness at the outside edge of the door
    • Pull back the door hinge boot
    • Disconnect the two wiring harnesses in the door hinge
    • Pull the wiring harnesses out through the door
    • Unclip the wiring harnesses from the door with a flat blade screwdriver
    • Pull the wiring harnesses through the regulator panel
    • Pull the door handle rod out through the panel
    • Pull the lock rod out through the panel
  4. Preparing the New Regulator Panel (6:31 in the video)
    • Drill the rivets out of the speaker on the old window regulator panel
    • Pry the speaker off of the old panel with a flat blade screwdriver
    • Transfer all the mounting clips from the old panel to the new panel
    • Transfer the rubber door from the old panel to the new panel
    • Transfer the wiring mounting clips from the old panel to the new panel
    • Push the speaker into place with the wiring harness pointing up
    • Rivet the speaker into place with the rivet gun
    • Remove the shipping wire tie
  5. Installing the New Regulator Panel (9:05 in the video)
    • Feed the wiring harnesses through the regulator panel
    • Feed the wiring harness through the door into the door hinge boot
    • Reconnect the harnesses in the door hinge
    • Push the boot into place
    • Push the wiring back onto its clips
    • Push the door lock rod through the regulator cable
    • Push the door lock rod onto its clips
    • Pull the door handle cable through the regulator
    • Reconnect the wiring harness at the outside edge of the door
    • Push the regulator into place
    • Push in the mounting clips in the upper right hand corner
    • Insert the 10mm bolts into the regulator panel
  6. Connecting the New Regulator Panel (12:02 in the video)
    • Slide the window down by hand
    • Push in the outer window clamp ring with needle nose pliers
    • Push in the inner window clamp ring with needle nose pliers
    • Push in the rubber cover
    • Push the window motor into place
    • Insert the three T30 Torx bolts into the window motor
    • Reconnect the lock rod cable to the lock rod
    • Connect the window motor wiring harness
    • Reconnect the speaker wiring harness
    • Reconnect the speaker cover if necessary
  7. Reinstalling the Door Panel (13:56 in the video)
    • Connect the two wiring harnesses to the door panel
    • Hook the door handle cable onto the door handle
    • Slide on the door handle cable clip
    • Push the door panel onto the window sill
    • Push in the door panel clips
    • Insert the two T20 Torx bolts into the bottom of the door panel
    • Insert the two Phillips screws into the door pull
    • Push on the door pull cover

Tools needed for replacement:

    Drills, Drill Bits & Related

  • 5/16 Inch Drill Bit
  • Drill

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Slip-Joint Pliers

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Specialty Tools

  • Rivet Gun & Rivets

  • Torx Drivers & Sockets

  • T20 Torx Driver
  • T30 Torx Driver

How-to Video:

(15:17 min)

Tools List:

    Drills, Drill Bits & Related

  • 5/16 Inch Drill Bit
  • Drill

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Slip-Joint Pliers

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Specialty Tools

  • Rivet Gun & Rivets

  • Torx Drivers & Sockets

  • T20 Torx Driver
  • T30 Torx Driver



This part replaces:

  • OE # 1J4839462F
  • HOLLANDER 135-58451R, 135-58455R
  • DORMAN 740-927

Vehicle Fit

  • 1999 VW Golf 4 Door Power Window Regulator (without Motor) Rear Passenger Side (Built After 10/01/98 Production Date)
  • 2000-2006 VW Golf 4 Door Power Window Regulator (without Motor) Rear Passenger Side
  • 1999 VW Jetta Power Window Regulator (without Motor) Rear Passenger Side (Built After 10/01/98 Production Date)
  • 2000-2004 VW Jetta Power Window Regulator (without Motor) Rear Passenger Side
  • 2005 VW Jetta (8th Vin Digit J or M) Power Window Regulator (without Motor) Rear Passenger Side
$62.45
Save 43%
List: $109.83 Save: $47.38
Part #: 1AWRG00363

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est