Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto 1 Year Warranty
Frequently bought together
Item Condition:
New
1 Year Warranty
This item is backed by our 1-year warranty. In the event this item should fail during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the evap purge canister on a 2006 Chevy Impala. The tools that you'll need are a pair of pliers. You'll also need a replacement purge canister from 1AAuto.com.
You're going to locate the evap purge canister behind the left rear wheel, kind of right by your gas tank on the inside of that fender. Go ahead and take off the connector that goes to it, and you're going to lift up on the tab and just slide it right out. You can see it right here up close to the tab that you pull up on. To get the canister down, you're going to want to pull backwards. Give it a little jiggle and pull it backwards. It's just being held on. It slides on to a clip. I'll show you, right here. The clip just slides in, right through there. You just pull it back and down. Using a pair of pliers, here, to squeeze that clamp, slide it down the end of the hose. Then, I'm going to go ahead and twist the rubber evap hose and the canister to get it off.
Here's a side-by-side of the old part and the exact new replacement part from 1A Auto. Going back in, I'm going to put the rubber flexible hose back on and use my pliers to secure the clip, so that there are no leaks. Once I've done that, I'm going to slide it back up into the fender well, the wheel well, and slide it back on to its bracket. It can be a little tough. You've got to just wiggle it and push it back on. Once you've got that in place, you can go ahead and reinstall your connector.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the evap purge solenoid on this 2005 GMC Savana 2500. It's similar on a large variety of GM models. The only tools that you're going to need for this are a flat blade screwdriver and some wire cutters.
To start off, we're just going to show you where you find this in between the door and the gas tank on this van. It's right under here. You look up, it's right here.
The first thing that you want to do is take your wire cutters and just clip off that wire tie. Then you can remove this cover. For now, because it's behind it, you can tuck it up. Pull that harness out, it just pulls right out.
Now, using a flat blade screwdriver, you want to push the clip down and slide the solenoid back, and it should come right off. Now, what you want to do is just disconnect the hose here. You can see here, new part from 1A Auto on the right, old part on the left. They're identical in every way, same mounting clip, and everything.
What you want to do is just put that cover back on to it. It just fits right on, and then you want to put it up back underneath the car.
You just want to angle that clip onto the clip underneath the van. It can be a little difficult because of the box there, but if you just pull that back, eventually once you get it lined up, you just twist it in and it should just slide right there.
Now what you want to do, reconnect the harness and that hose, and now you can put a wire tie so that cover stays on. Then you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
