Replaces

2004-2010 Mazda B2300 Truck Turn Signal and Wiper Switch Lever

This part replaces:

  • HOLLANDER 629-00665, 629-00486
  • STANDARD MOTOR PRODUCTS CBS-1158
  • OE # 4C3Z-13K359-AAA, 1FAA-66-130, 1F70-66-130, 1F70-66-130A, 1FAA-66-130, 4C3T-13K359-ACJ

  • New

This turn signal lever is a new, aftermarket replacement part. It is designed to REPLACE original units that are prone for failure. It's just what you need to get your vehicle in good working order again!

Specifications:

  • Includes wiper controls
  • Exact replacement
  • Design improved for more durability
  • Detailed graphics
  • Built to strict quality control standards

This combination turn signal & wiper lever makes great replacement and has substantial cost savings over a dealer unit.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Disconnecting the Battery (0:27 in the video)
    • Use an 8mm wrench to disconnect the negative battery cable
  2. Removing the Dash Trim (0:40 in the video)
    • Pry out the headlight switch with a flat blade screwdriver
    • Disconnect the wiring connections from the headlight switch
    • Unsnap the dash trim
    • Move the shifter down
    • Undo the cigarette lighter wiring connector and the airbag switch connector
    • Disconnect the antenna wire from the radio
    • Disconnect the radio wiring connection
    • Pull off the dash panel
    • Remove the radio from the dash panel
  3. Removing the Steering Column Trim (2:53 in the video)
    • Use the Torx driver to unlock the lock cylinder locking pin
    • With the key in the on position push the lock cylinder in
    • Remove the lock cylinder
    • Remove the steering wheel tilt lever with an adjustable wrench
    • Remove the three Phillips head screws from the lower steering column trim
    • Pull off the lower steering column trim
    • Pull off the upper steering column trim
  4. Removing the Multifunction Switch (4:12 in the video)
    • Remove the two T20 Torx screws from the multifunction switch
    • Pull the switch free of the steering column
    • Disconnect the wiring connectors
  5. Installing the New Multifunction Switch (4:47 in the video)
    • Connect the wiring connectors to the new switch
    • Put the switch in place
    • Insert the two T20 Torx screws
  6. Reinstalling the Steering Column Trim (5:35 in the video)
    • Put the upper steering column trim panel in place
    • Put the lower steering column trim panel in place
    • Snap the steering column trim together
    • Insert the three Phillips head screws in the lower steering column trim
  7. Reinstalling the Dash Trim (6:21 in the video)
    • Put the dash panel into place
    • Reconnect the airbag switch connector and the cigarette lighter connector
    • Loosen the two 7mm bolts in the radio outlet
    • Push the panel on
    • Tighten the two 7mm bolts
    • Connect the wiring connector to the radio
    • Connect the antenna wire to the radio
    • Slide in the radio
    • Connect the wiring connectors to the headlight switch
    • Slide the headlight switch in
    • Insert the ignition lock cylinder with the locking pin on the bottom
  8. Reconnecting the Battery (8:04 in the video)
    • Reconnect the negative battery cable

Tools needed for replacement:

    Pliers, Cutters & misc Wrenches

  • Adjustable Wrench

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 7mm Socket

  • Torx Drivers & Sockets

  • T20 Torx Driver

  • Wrenches - Metric

  • 8mm Wrench

How-to Video:

(08:32 min)

Tools List:

    Pliers, Cutters & misc Wrenches

  • Adjustable Wrench

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 7mm Socket

  • Torx Drivers & Sockets

  • T20 Torx Driver

  • Wrenches - Metric

  • 8mm Wrench



This part replaces:

  • HOLLANDER 629-00665, 629-00486
  • STANDARD MOTOR PRODUCTS CBS-1158
  • OE # 4C3Z-13K359-AAA, 1FAA-66-130, 1F70-66-130, 1F70-66-130A, 1FAA-66-130, 4C3T-13K359-ACJ

Vehicle Fit

  • 2002-2007 Ford F250 Super Duty Truck Turn Signal and Wiper Switch Lever
  • 2002-2007 Ford F350 Super Duty Truck Turn Signal and Wiper Switch Lever
  • 2002-2003 Ford F450 Truck Turn Signal and Wiper Switch Lever
  • 2002-2003 Ford F550 Truck Turn Signal and Wiper Switch Lever
  • 2004-2011 Ford Ranger Turn Signal and Wiper Switch Lever
  • 2004-2010 Mazda B2300 Truck Turn Signal and Wiper Switch Lever
  • 2004-2008 Mazda B3000 Truck Turn Signal and Wiper Switch Lever
  • 2004-2010 Mazda B4000 Truck Turn Signal and Wiper Switch Lever
$73.45
Save 25%
List: $97.96 Save: $24.51
Part #: 1AZTS00082

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est