Replaces

1997-2001 Toyota Camry Strut & Spring Assembly 4 Piece Set for L4 2.2L

Part Details

  • Quantity: 4 Piece Set

  • New

Designed for easier installation.

This SET of 4 are a new replacement strut and spring assemblies. We recommend after replacing struts that a alignment should be done.

Specifications:

  • Comes as a SET of 4
    • Fits both the LH (Driver) & RH (Passenger) Side FRONT & REAR
  • Each strut includes:
    Replacement upper mount
    Upper and lower spring isolators
    Upper spring seat
    Coil spring
    Boot kit
  • Preassembled for easier replacement
  • Correct for models with L4 2.2L Engine

In the past, replacing struts required specialized tools to compress, remove and transfer the spring. Our new strut and spring assemblies make this job much simpler for the do it yourself mechanic. This part comes preassembled. Jack up and support the vehicle with jack stands. Remove the wheel. Unbolt the top mounts and the bottom from the suspension and replace the whole unit. The large bottom bolts usually require an impact wrench and socket for removal. When reassembling, be sure to torque all nuts and bolts to their proper specifications. Do not use impact tools when reassembling.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Wheel (1:14)
    • Pull off the hub cap by hand
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. Removing the Strut (1:37)
    • Remove the 12mm bolt from the brake line
    • Remove the 10mm bolt from the ABS sensor
    • Pull the brake line off the strut
    • Pull the ABS sensor off the strut
    • Attach locking pliers to the upper sway bar ball joint
    • Remove the lower sway bar link nut with a 14mm socket and ratchet
    • Remove the sway bar link from the strut
    • Remove the two 19mm nuts and bolts that connect the strut to the wheel spindle
    • Lift the rear seat off its ancho points
    • Push the seat belts through the rear seat cushion
    • Pull the rear seat out through the door
    • Remove the 12mm bolt from each rear seat bolster
    • Pull out the rear seat bolsters
    • Pull the seatbelt aside
    • Pull back the sound-deadening material
    • Remove the three 12mm bolts from the top of the strut
    • Pull the strut down and out
  3. Installing the Strut (5:44)
    • Lift the strut into place, lining up the studs
    • Start the 13mm nuts onto the strut mount
    • Insert the 19mm bolts that connect the strut to the wheel spindle
    • Start the 19mm nuts onto the bolts
    • Tighten the 19mm nuts to 83 foot-pounds of torque
    • Put the ABS sensor bracket into place
    • Insert the 10mm bolt into the ABS sensor bracket
    • Put the brake line into place
    • Insert the 12mm bolt into the brake line bracket
    • Put the sway bar link into place
    • Attach locking pliers to the upper sway bar ball joint
    • Fasten the 14mm nut onto the sway bar link
  4. Reattaching the Wheel (7:31)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 76 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  5. Securing the Strut and Reinstalling the Rear Seat (8:08)
    • Fasten the three 13mm nuts onto the strut mount
    • Push the rear seat bolsters into place using the locating tabs
    • Insert the 12mm bolt into each rear seat bolster bracket
    • Push the rear seat cushion into place
    • Pull the seatbelts through the rear seat cushion
    • Pop in the seat cushion clips

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 21mm Socket
  • 19mm Socket
  • 14mm Socket
  • 12mm Socket
  • 13mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 21mm wrench
  • 14mm Wrench
  • 19mm Wrench
  • 10mm Wrench
  • 13mm Wrench
  • 12mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(09:40 min)

Tools List:

    General Tools

  • Jack Stands
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 21mm Socket
  • 19mm Socket
  • 14mm Socket
  • 12mm Socket
  • 13mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 21mm wrench
  • 14mm Wrench
  • 19mm Wrench
  • 10mm Wrench
  • 13mm Wrench
  • 12mm Wrench




Vehicle Fit

  • 1997-2001 Toyota Camry Strut & Spring Assembly 4 Piece Set for L4 2.2L
  • 1999-2003 Toyota Solara Strut & Spring Assembly 4 Piece Set for L4 2.2L
$ 284.95
Save 68%
List: $897.95 Save: $613.00
Part #: 1ASFK00096

Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY M-F
For Orders Placed By 5pm Est