Replaces

1995-1997 Dodge Intrepid Timing Belt Kit with Water Pump for V6 3.5L with 3 Bolt Water Pump ( Gates)

This part replaces:

  • Gates TCKWP255

  • New

Gates (TCKWP255) Water Pump and Timing Belt Component Kit

This Gates timing belt component kit, tensioner with water pump is just what you need to keep your vehicle in good running order.

Our timing belt sets come from a company that is committed to supplying components that are engineered and manufactured under strict quality control procedures. They are leaders in timing component quality which provides you with the highest quality parts available on the market.

This high quality, water pump and timing belt kit, contains the following pieces and has the following specifications:

  • (1) - Timing Belt
  • (1) - Hydraulic tensioner
  • (1) - Tensioner
  • (1) - Water pump
  • (1) - Water pump gasket

Correct for Models with 3 Bolt Water Pump

Most car manufacturers recommend changing your timing belt between 50,000 and 70,000 miles (consult your owner's manual to see what your specific manufacturer suggests).

Note:
These parts are authentic Gates brand products that are supplied and packaged by Gates. Some of the components included in this kit may be sourced by Gates from other high quality suppliers such as Aisin, GMB, Koyo & other OEM suppliers. These parts are subjected to the very same testing and quality standards as all Gates products.

2 Year Warranty

This item is backed by a 2 Year Warranty. In the event this item should fail during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Gates Limited Warranty

Purchase with Confidence. Gates is committed to quality!

Merchandise is warrantied to be free from defects in material or workmanship for 18 months from the date of delivery to Purchaser. The Gates Corporation will, at its option, replace or repair any merchandise proved defective in material or workmanship, or both, during the warranty period. This shall be the sole remedy for breach of warranty. All other warranties, express or implied, including, but not limited to, warranties of merchantability or fitness for a particular purpose, hereby are expressly disclaimed. liability for consequential, incidental, special, exemplary and indirect damages, including, but not limited to, lost profits, hereby are expressly excluded, regardless of whether they were reasonably foreseeable, or whether seller had knowledge that they could occur. Exclusion of Warranty The warranty shall be void to the extent that any of the following occurs: (a) improper installation of the Products into vehicles; or (b) improper usage by Purchaser ; or (c) induction of defect by other products; or (d) mishandling of the Products or other abuse; or (e) improper matching with other applications; or (f) collision, engine overheating or oil starvation, product contamination, including, but not limited to, with oil or antifreeze; or (g) the Products are used for racing or competition; or (h) any use not recommended in writing by Gates.

  1. Step 1: Watch Part 1 of This Video ( in the video)
    • Remove the six bolts holding the water pump.
    • Use a screwdriver to pry the top side of the water pump.
    • Remove the water pump and clean up any coolant that comes up.
    • Press the o-ring into place on the new water pump.
    • Long bolt goes in the top left. Line the water pump up and push it into place.
    • Tighten the 10mm bolts. Torque to 110 inch/lbs or 9ft/lbs. (Do this in a star pattern).
  2. Step 2: Changing the Water Pump (0:30 in the video)
    • Remove the six bolts holding the water pump.
    • Use a screwdriver to pry the top side of the water pump.
    • Remove the water pump and clean up any coolant that comes up.
    • Press the o-ring into place on the new water pump.
    • Long bolt goes in the top left. Line the water pump up and push it into place.
    • Tighten the 10mm bolts. Torque to 110 inch/lbs or 9ft/lbs. (Do this in a star pattern).
  3. Step 3: Changing the Tensioner Pulley (3:00 in the video)
    • Remove the 15mm bolt securing the tensioner pulley.
    • Put the new pulley into place.
    • Tighten the 15mm bolt to 45-55ft/lbs.
  4. Step 4: Replace the Timing Belt (3:28 in the video)
    • Put the belt into place. (over the top cam shaft and down around the crank, and over the top of the cam shaft on the opposite side.
    • Insert the tensioner and tighten the bolts evenly.
    • Remove the pin. Tighten bolts to 25-30ft/lbs.
    • Rotate the crank shaft twice.
    • Line up the dots on the cam shafts and the line on the crank shaft.
    • If it’s wrong loosen up the tensioner and pull the belt off and turn the cam shaft. Replace the belt and tighten the tensioner.
    • Remove the bolt from the crank shaft.
  5. Step 5: Reinstalling the Covers and Belts (8:16 in the video)
    • Put the cast cover on and replace the bolts.
    • Put the stamped steel cover on and replace the bolts.
    • Tighten the bolts to 9-11ft/lbs.
    • Replace the crankshaft pulley and replace the bolts.
    • Use the belt wrench and tight the pulley bolt 80-85ft/lbs
    • Put the tensioner pulley on. Replace the three 13mm bolts. Tighten to 25-30ft/lbs
    • Put the ACV belt into place.
    • Put the grooved serpentine belt into place.
  6. Step 6: Reinstalling the Radiator (9:52 in the video)
    • Make sure the drain plug is tightened.
    • Push the radiator into place and make sure no hoses are caught underneath.
    • Start the bolts.
    • Push the radiator line bracket back into place and replace the bolt.
    • Replace the two front radiator bolts.
    • Reinstall the upper transmission cooler line and use a screwdriver to tighten the clamp.
    • Use pliers to squeeze the clamp and reconnect the upper radiator hose.
    • Replace the top brace back into place and replace the bolts.
    • Start the bolts that hold the condenser to the radiator starting with the bottom bolts. Tighten them.
    • Put the lower transmission cooler line on and tighten up the clamp.
    • Connect the lower radiator hose by pushing the clamp and connecting it to the radiator.
  7. Step 7: Tighten the Belts (12:52 in the video)
    • Tighten the tensioners on each belt so that they do not have more than a 1/4" of slack.
    • Use a 15mm socket to tighten the nut on the pulley.
    • Reconnect the radiator fan.
    • Use a 15mm wrench to tighten the nut on the upper tensioner pulley.
    • Reconnect the battery.
  8. Step 8: Filling the Car with Coolant (13:52 in the video)
    • Start it to make sure the timing belt is ok.
    • Fill it with coolant.
    • Run the car to circulate the coolant.
    • Top it off with more coolant.

Tools needed for replacement:

    Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 13mm Socket
  • 15mm Socket

  • Specialty Tools

  • Belt Wrench
  • Drain Pan
  • Jack Stands

  • Wrenches - Metric

  • 18mm Wrench

How-to Video:

(15:33 min)

Tools List:

    Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 13mm Socket
  • 15mm Socket

  • Specialty Tools

  • Belt Wrench
  • Drain Pan
  • Jack Stands

  • Wrenches - Metric

  • 18mm Wrench



This part replaces:

  • Gates TCKWP255

Vehicle Fit

  • 1995-1996 Chrysler New Yorker Timing Belt Kit with Water Pump for V6 3.5L with 3 Bolt Water Pump ( Gates)
  • 1995-1997 Dodge Intrepid Timing Belt Kit with Water Pump for V6 3.5L with 3 Bolt Water Pump ( Gates)
  • 1995-1997 Eagle Vision Timing Belt Kit with Water Pump for V6 3.5L with 3 Bolt Water Pump ( Gates)
  • 1997 Plymouth Prowler Timing Belt Kit with Water Pump for V6 3.5L with 3 Bolt Water Pump ( Gates)
$154.45
Only 2 left in stock
Part #: GAEEK00070

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates
GATES
Brand #: TCKWP255

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est