Replaces

Tie Rod Front Pair - 1ASFK00067

Part Details

  • Location: Outer
  • Front / Rear Location: Front
  • Quantity: Pair

  • New

Your outer tie rod end connects the inner tie rod sleeve and end to the front spindle or knuckle. Over time the greasable joint can wear causing loose connections and a sloppy steering feel.

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) and RH (Passenger Side) OUTER
  • Comes as shown with greasable joint
  • Built to strict quality control standards
  • Direct replacement

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. When installed correctly and an alignment performed, this tie rod end set could also reduce uneven tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

    It is recommended to receive a professional alignment after completing this repair

  1. Removing the Wheel (0:43)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. Removing the Outer Tie Rod (1:05)
    • Use a pair of pliers to straighten the cotter pin and remove it
    • Remove the castle nut with an adjustable wrench
    • Measure the distance from the inner tie rod to the outer tie rod
    • Loosen the nut between the inner and outer tie rod
    • Hammer the knuckle to loosen the outer tie rod
    • Remove the outer tie rod and twist it off the inner tie rod
  3. Installing the Outer Tie Rod (2:05)
    • Twist the grease filler into the new outer tie rod
    • Twist the outer tie rod to the inner tie rod
    • Measure the distance and make sure it matches the recorded distance
    • Tighten the nut between the inner and outer tie rod
    • Insert the outer tie rod to the knuckle
    • Replace and tighten the castle nut while lining up the cotter pin hole
    • Insert the cotter pin and twist the ends with a pair of pliers
    • Fill up the grease filler with a grease gun
  4. Reattaching the Wheel (3:21)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Hammer
  • Measuring Tape
  • Floor Jack
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Needle nose pliers

  • Specialty Tools

  • Grease Gun


How-to Video:

(03:52 min)

Tools List:

    General Tools

  • Hammer
  • Measuring Tape
  • Floor Jack
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Needle nose pliers

  • Specialty Tools

  • Grease Gun




Vehicle Fit

  • 1995-2000 Chrysler Cirrus Front Outer Tie Rod Pair
  • 1996-2005 Chrysler Sebring Convertible Front Outer Tie Rod Pair
  • 2001-2005 Chrysler Sebring Sedan Front Outer Tie Rod Pair
  • 2006 Chrysler Sebring Front Outer Tie Rod Pair
  • 1995-2000 Dodge Stratus Front Outer Tie Rod Pair
  • 2001-2005 Dodge Stratus Sedan Front Outer Tie Rod Pair
  • 2006 Dodge Stratus Front Outer Tie Rod Pair
  • 1996-2000 Plymouth Breeze Front Outer Tie Rod Pair
$34.95
Save 62%
List: $91.95 Save: $57.00
Part #: 1ASFK00067

Out of Stock

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est