Replaces

Tie Rod Front Driver Side - 1ASTE00017

Part Details

  • Location: Outer
  • Front / Rear Location: Front
  • Side Location: Driver Side

  • New

Your outer tie rod end connects the inner tie rod sleeve and end to the front spindle or knuckle. Over time the greasable joint can wear causing loose connections and a sloppy steering feel.

Specifications:

  • Fits LH (Driver Side) OUTER
  • Comes as shown with greasable joint
  • Built to strict quality control standards
  • Direct replacement

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. When installed correctly and an alignment performed, this tie rod end could also reduce uneven tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Wheel (0:43 in the video)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. Removing the Outer Tie Rod (1:05 in the video)
    • Use a pair of pliers to straighten the cotter pin and remove it
    • Remove the castle nut with an adjustable wrench
    • Measure the distance from the inner tie rod to the outer tie rod
    • Loosen the nut between the inner and outer tie rod
    • Hammer the knuckle to loosen the outer tie rod
    • Remove the outer tie rod and twist it off the inner tie rod
  3. Installing the Outer Tie Rod (2:05 in the video)
    • Twist the grease filler into the new outer tie rod
    • Twist the outer tie rod to the inner tie rod
    • Measure the distance and make sure it matches the recorded distance
    • Tighten the nut between the inner and outer tie rod
    • Insert the outer tie rod to the knuckle
    • Replace and tighten the castle nut while lining up the cotter pin hole
    • Insert the cotter pin and twist the ends with a pair of pliers
    • Fill up the grease filler with a grease gun
  4. Reattaching the Wheel (3:21 in the video)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Needle nose pliers

  • Specialty Tools

  • Floor Jack
  • Grease Gun
  • Hammer
  • Jack Stands
  • Measuring Tape

How-to Video:

(03:52 min)

Tools List:

    Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Needle nose pliers

  • Specialty Tools

  • Floor Jack
  • Grease Gun
  • Hammer
  • Jack Stands
  • Measuring Tape




Vehicle Fit

  • 1995-2000 Chrysler Cirrus Front Outer Tie Rod End Driver Side
  • 1996-2005 Chrysler Sebring Convertible Front Outer Tie Rod End Driver Side
  • 2001-2005 Chrysler Sebring Sedan Front Outer Tie Rod End Driver Side
  • 2006 Chrysler Sebring Front Outer Tie Rod End Driver Side
  • 1995-2000 Dodge Stratus Front Outer Tie Rod End Driver Side
  • 2001-2005 Dodge Stratus Sedan Front Outer Tie Rod End Driver Side
  • 2006 Dodge Stratus Front Outer Tie Rod End Driver Side
  • 1996-2000 Plymouth Breeze Front Outer Tie Rod End Driver Side
$29.45
Only 4 left in stock
Part #: 1ASTE00017

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est