Replaces

2003-2009 GMC Envoy Front Suspension Kit (6 Piece)

Part Details

  • Front / Rear Location: Front
  • Quantity: 6 Piece

  • New

These replacement suspension parts are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • FRONT Suspension Kit includes:
    • (2) - FRONT OUTER Tie Rod Ends - LH (Driver Side) & RH (Passenger Side)*
    • (2) - FRONT LOWER Ball Joints - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT UPPER Ball Joints - LH (Driver Side) & RH (Passenger Side)
  • Replaces dealer part numbers: 26100286, 26100287, 22157319, 19133670, 8191336700, 22157320
  • Parts are new, not remanufactured or refurbished
  • Direct replacements
  • Built to strict quality control standards

*NOTE: For 2002 Models, there were two different tie rod options available: 1st design (14mm thread) & 2nd design (16mm thread). This tie rod is correct for models with the 2nd design tie rods.

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Wheel (0:46 in the video)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. Removing the Ball Joint (1:11 in the video)
    • Separate the axle from its housing with a pry bar and a hammer
    • Unclip the brake line from its clips
    • Remove the ball joint retaining ring with a hammer and punch
    • Remove two 10mm bolts from the steering knuckle bracket
    • Apply penetrating oil to the control arm nut and bolt
    • Remove the 15mm nut and bolt from the control arm
    • Strike the control arm with a hammer to loosen it
    • Pull the steering knuckle forward
    • Support the wheel knuckle with wire ties
    • Cut off the ball joint boot with a razor
    • Fit a ball joint press to the ball joint
    • Tighten the press to press out the ball joint
    • Remove the ball joint press
    • Tap out the ball joint with a hammer
  3. Installing the New Ball Joint (4:22 in the video)
    • Push the new ball joint into place
    • Fit the ball joint press onto the ball joint
    • Tighten the ball joint press to press in the ball joint
    • Tap the ball joint in with a hammer
    • Tap the snap ring into place with a hammer and punch
    • If you are replacing the snap ring, put the new ring on with snap ring pliers
    • Push the steering knuckle into place
    • Push the control arm onto the ball joint
    • Tap the control arm onto the ball joint with a hammer
    • Start the 15mm nut and bolt into the control arm
    • Remove the wire ties from the steering knuckle
    • Push the axle into its housing
    • Tighten the 15mm nut to 50 foot-pounds of torque
    • Fasten the grease fitting onto the ball joint with a 10mm wrench
    • Add grease to the ball joint with a grease gun
    • Insert the two 10mm bolts into the steering knuckle bracket
    • Clip the brake line into place
  4. Reattaching the Wheel (7:00 in the video)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Bearing Grease
  • Rust Penetrant
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 10mm Socket
  • 15mm Socket
  • 19mm Socket

  • Specialty Tools

  • Ball Joint Press
  • Floor Jack
  • Grease Gun
  • Hammer
  • Jack Stands
  • Razor Blade / Gasket Scraper

  • Wrenches - Metric

  • 10mm Wrench
  • 15mm Wrench

How-to Video:

(07:51 min)

Tools List:

    Materials, Fluids, and Supplies

  • Bearing Grease
  • Rust Penetrant
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 10mm Socket
  • 15mm Socket
  • 19mm Socket

  • Specialty Tools

  • Ball Joint Press
  • Floor Jack
  • Grease Gun
  • Hammer
  • Jack Stands
  • Razor Blade / Gasket Scraper

  • Wrenches - Metric

  • 10mm Wrench
  • 15mm Wrench




Vehicle Fit

  • 2004-2007 Buick Rainier Front Suspension Kit (6 Piece)
  • 2002 Chevy Trailblazer Suspension Kit Front (6 Piece) (16 mm Thread)
  • 2003-2009 Chevy Trailblazer Front Suspension Kit (6 Piece)
  • 2003-2005 Chevy Trailblazer EXT Front Suspension Kit (6 Piece)
  • 2002 GMC Envoy Suspension Kit Front (6 Piece) (16 mm Thread)
  • 2003-2009 GMC Envoy Front Suspension Kit (6 Piece)
  • 2003-2004 GMC Envoy XL Front Suspension Kit (6 Piece)
  • 2003-2008 Isuzu Ascender Front Suspension Kit (6 Piece)
  • 2002 Olds Bravada Suspension Kit Front (6 Piece) (16 mm Thread)
  • 2003-2004 Olds Bravada Front Suspension Kit (6 Piece)
  • 2005-2007 Saab 9-7X Front Suspension Kit (6 Piece)
$74.95
Save 91%
List: $828.43 Save: $753.48
Part #: 1ASFK00730

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est