Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Left Hand Drive:
All of our auto parts are intended for Left Hand Drive USDM vehicles. If your vehicle is Right Hand Drive, please ensure the part is correct for your specific vehicle.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the A/C and heater van speed resistor on this 2006 Nissan Sentra. It's not a hard repair, but it is a little difficult just getting in underneath there and the angles. The only tools you'll need are a regular Phillips screwdriver and a short Phillips screwdriver.
We're inside. What you want to do is open up your glove compartment and basically what I'm doing is pushing to the side firmly. Then, you can pull your whole glove box right down. Now your resistor is right up under here. It's this connection here. You can press a tab and pull that down. You can see that there are two screws that hold it in. Basically, finding it is the toughest part. Once you get down here loosen up that clip, move it out of the way, and I loosened that easier-to-see screw first. Then I use a short screwdriver to loosen up the one that's back closest to the firewall of the car. Take that out then take the other screw all the way out. Once I have that screw out then I just pull the resistor right down and out.
Here's our original one and then you can see our replacement one is exactly the same. Here again I'm just going to speed through this. It's basically a matter of putting the resistor up in there and then, basically, you want to start the screws by hand and just the difficult part is the kind of the bad angle that this is at. Once you put the resistor up in there, you should be able to press it in enough. It should stay in place. Then you can put the screws in, start them in, then use your screwdriver and tighten them up. Once you have those tight, then you can reconnect your harness and you can tighten up that clip or that bracket that holds the lower panel on. Now the tabs on this panel go up into those white clips. Clip it in and then bring this up and on there like that. Now do a little more fast forward as I just put the two screws that hold that panel in. Put your glove box back in. Just kind of tuck it in, push it to the side, and it's all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the blower motor resistor in this 2003 Nissan Frontier. Most often, the symptoms of a bad blower motor resistor are that your fan will not work on all the speeds: either high or low or maybe none. In order to replace this you will need a Phillips head screwdriver as well as a new blower motor resistor from 1A Auto.
Locate the blower motor resistor underneath the glove box. You see the connector and two Phillips head screws which hold it in place. Press the connector, pull it down and push it out of the way. Then with your Phillips head screwdriver, remove the two screws.
Here you see the old part and the new part from 1A Auto. They're identical and it's a direct replacement fit. Line up your new resistor with the slot. Press it in. Begin reinstalling your two Phillips head screws and then you can plug your connector back in.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
