TRQ ignition coils will have your engine running like new. TRQ ignition coils are manufactured to precise specifications using premium raw materials to optimize each vehicle's ignition system. To ensure peak performance, TRQ recommends replacing ignition coils in sets to prevent electrical output imbalances. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
High dielectric epoxy and reinforced bobbins for extended service life
Rubber, Silicone, or Phenolic Resin Shell: Prevents premature boot wear
Application Specific Design: No modifications required
Complete repair to restore your engine to like-new condition
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Ignition Coil 2004-06 Chevy Colorado
How To Replace Ignition Coil 2002-2009 Chevrolet Trailblazer
Created on:
Tools used
10mm Socket
8mm Socket
Flat Blade Screwdriver
Ratchet
Socket Extensions
1. Removing the Air Intake Box
Remove the two 8mm bolts holding the top of the air box
Remove the two hose clamps with a flat blade screwdriver
Twist and remove the two vacuum lines
Pull the air intake box up and out
Twist the air intake hose collar off
2. Removing the Ignition Coil
Disconnect the locking tab with a flat blade screwdriver
Disconnect the ignition coil wiring harness
Remove the 10mm bolt from the engine coil
Pull the ignition coil up and out
3. Installing the New Ignition Coil
Insert the ignition coil into place
Insert and tighten the 10mm bolt
Connect the ignition coil wiring lead
Replace the locking pad
4. Installing the Air Intake Box
Twist the air intake hose collar into place
Insert the air intake box into place
Insert the two vacuum lines
Insert and tighten the two hose clamps with a flat blade screwdriver
Insert and tighten the two 8mm bolts holding the top of the air box
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace ignition coil. On these vehicles, they recommend you replace these coils at 100,000 miles. Also, sometimes if your engine runs a little rough and turns the "check engine" light on and you get a code that says, "Cylinder 1 or Cylinder 3 or something misfiring," that's usually a coil going bad. It is a pretty easy replacement. You'll need a ratchet extension with 8mm and 10mm sockets. If you don't have an 8mm socket, a flat blade screwdriver can help you get the clamps off as you'll see.
Working from the passenger side, you want to remove two bolts that hold the top of the air box: one here and one right here. Now to remove this, you want to remove this intake tube which is a clamp here and a clamp here. Remove that tube and then loosen both this one and this one to pull this apart. I'll speed this up a little bit. You can either use a flat blade screwdriver or an 8mm socket with a ratchet and extension to undo those clamps. This also has a small vacuum line on here. Twist and pull that off, and then this goes up, and there's also a line right back here. Just pull off of there.
This big vehicle has been sitting for a while, so I'm just using a vacuum cleaner to clean up the vacated mouse house that's sitting on the intake. Okay, then take, twist, and get this collar off here. You can see here are our five coils. Pick any one of them, and just remove the 10mm bolt. Each of them have a little gray clip that you just pull on. Use a screwdriver. There's a little tab right in the center. Push the tab down and pull the clip right off.
Then there's just a tab for your thumb. Press that. Remove the lead, remove this 10mm bolt, and then, once you have the bolt removed, just move it around, shake it up and down a little bit, and then the coil comes up and out.
The new coil from 1A Auto is exactly the same as the old one. Put it right down in. You want to just push it straight in. Tighten up the 10mm bolt. Plug your lead back in, and then put the locking tab back in place. Repeat that for any cylinders you need. The cylinder order on these is usually just from front to back: 1, 2, 3, 4 and 5. If you get a code like "number 3 cylinder misfiring," that's usually a bad coil, so you'd replace the number 3 coil.
To put it back together, put this on there. There's a little notch that should stick up right there. I've got my two bolts already kind of in there. Right here is that hose. Push that hose down first. Put this down in place. I'm just kind of maneuvering it into this hose here. Push it into place and twist this hose a little bit off. Push it down onto here. Get it good and tight on there. Hook up the vacuum hose. Use an 8mm socket to tighten up. Just inspect where the hoses go and their housings. Make sure they're nice and tight, and then tighten up our clamps. Again, you can use either a flat blade screwdriver or an 8mm socket. Then we go back to our 10mm socket and then tighten them up and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Dielectric Grease
Flat Blade Screwdriver
Phillips Head Screwdriver
10mm Socket
Trim Tool Set
ICA61606
In Stock
Product Reviews
Loading reviews
5.00/ 5.07
7 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
7
0
0
0
0
Working good
Antonios
June 30, 2017
Good product.
I put it to my car and working very good .
I recommend it
Cost verses prefromance
R
August 10, 2018
Performs great, like the original GMC parts that cost so much more money. My truck is running great.
Awesome price
Sara
October 9, 2018
The coils were exactly as described and cost half of what I could have paid for them in town. Will definitely be buying my parts from 1aauto.com from now on.
Sydney
August 24, 2020
These parts are awesome ,100% satisfactory
Definitely recommend
Allen
December 17, 2020
what a great price for a quality product. I will buy from them again!
Coils for Trailblazer
Jack
June 27, 2021
Quality coils immediately resolved my problems. Time will tail if they were worth it. They were literally half price from what was available at local parts stores. Shipped quickly arrived in a few days excellent
Wade
February 3, 2022
Came in a timely manner, and perfect match, would definitely recommend this product.
Customer Q&A
What brand are the coils?August 18, 2021
John D
10
These are manufactured by TRQ. TRQ is a high quality, high-end name brand that we offer and back with our 1A Auto Limited Lifetime Warranty.
August 18, 2021
Jessica D
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.