Replaces

1992-1998 Honda Civic Front CV Axle Shaft Driver Side

Part Details

  • Front / Rear Location: Front
  • Side Location: Driver Side

This part replaces:

  • Hollander 447-59759L

  • New

This axle shaft is a new, aftermarket part. It is just what you need to get your vehicle in good working order!

Specifications:

  • Brand new, not rebuilt
  • No core charge
  • Fits LH (Driver Side)
  • 36 1/4" Long
  • 26 Outer Splines
    • Not correct for models with 23 spline outer joint
  • 25 Inner Splines

Axle shafts may need replacing for a variety of different reasons. On vehicles that do heavy work or endure other extreme use you can actually break an axle or strip the splines or teeth. More often the CV joint wears out causing noises and vibration while accelerating or turning.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

    We recommend an alignment after completing this repair

  1. Removing the Wheel (0:50)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. Removing the Hub Nut (1:27)
    • Remove the center cap from the wheel
    • Slide the wheel into place
    • Lower the vehicle to the ground
    • Have an assistant hold the brakes
    • Remove the 32mm nut with a large breaker bar
    • Secure the vehicle on jack stands
    • Pull off the wheel
    • Check to make sure the axle is free from the hub
  3. Removing the Caliper (2:03)
    • Remove the 12mm bolt from the brake hose
    • Remove the 10mm bolt from the sensor wire
    • Remove the 12mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Secure the caliper up in place with wire ties
  4. Removing the Axle (2:58)
    • Remove the 21mm pinch nuts and 19mm bolts
    • Pull the wheel knuckle out
    • Pry the axle out with a pry bar
    • Place a drain pan beneath the transmission
    • Pry the axle out of the transmission with a pry bar
  5. Installing the Axle (4:39)
    • Insert the axle into the transmission
    • Remove the new 32mm nut from the axle splines
    • Insert the axle into the wheel knuckle
    • Insert the 21mm pinch nuts and 19mm bolts into place
    • Hand tighten the 32mm hub nut
  6. Reinstalling the Caliper (6:10)
    • Place grease on your brake pads
    • Lower the caliper into place
    • Thread 12mm bolts by hand
    • Tighten bolts to 34 Newton Meters or 25 foot-pounds
    • Tighten the 10mm bolt to the sensor wire
    • Tighten the 12mm bolt to the brake hose
  7. After tightening, you might have to take the wheel off and dent the hub nut

  8. Reattaching the Wheel (7:39)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the 19mm lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern
    • Tighten the hub nut to 134 foot-pounds or 181 Newton Meters
    • Replace the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Drain Pan
  • Assistant
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 32mm Socket
  • 21mm Socket
  • 19mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 21mm wrench
  • 19mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(08:53 min)

Tools List:

    General Tools

  • Jack Stands
  • Hammer
  • Drain Pan
  • Assistant
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 32mm Socket
  • 21mm Socket
  • 19mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 21mm wrench
  • 19mm Wrench



This part replaces:

  • Hollander 447-59759L

Vehicle Fit

  • 1988-1991 Honda CRX Front CV Axle Shaft Driver Side (excluding HF Models)
  • 1988-1991 Honda Civic 2 Wheel Drive Front CV Axle Shaft for Automatic Transmission Driver Side
  • 1992-1998 Honda Civic Front CV Axle Shaft Driver Side
  • 1999-2000 Honda Civic Front CV Axle Shaft Driver Side (excluding SI Models)
  • 2001-2005 Honda Civic Coupe Front CV Axle Shaft for Models with for Automatic Transmission Driver Side
  • 2002-2005 Honda Civic Sedan Front CV Axle Shaft for Models with for Automatic Transmission Driver Side
  • 1993 Honda Civic Del Sol Front CV Axle Shaft Driver Side
  • 1994-1997 Honda Civic Del Sol Front CV Axle Shaft Driver Side (excluding VTEC)
$61.95
Part #: 1AACV00006

Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est