Replaces

1992-2013 Ford E350 Van Power Window Motor Front Pair

Part Details

  • Quantity: Pair

  • New

These power window motors are just what you need to get your vehicle in good shape again! If your window regulators are good, but the motors are burned out, then these are the parts for you.

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) and RH (Passenger Side) FRONT or REAR as listed by application
  • Brand New
    • No core charges
  • Replaces dealer part numbers: 1C2Z-1523200-AA, 1C2Z-1523201-AA, 9C2Z-1523201-A, F1TZ-78233V94-BRM, F1TZ-78233V95-BRM, 1C2Z1523200AA, 1C2Z1523201AA, 9C2Z1523201A, F1TZ78233V94BRM, F1TZ78233V95BRM
  • Direct replacements
  • Built to strict quality control standards

These window motors make great replacements and have good cost savings over dealer units.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Door Panel (1:14 in the video)
    • Use a flat blade screwdriver to pry off the bezel inside the door pull
    • Use a flat blade screwdriver to pry off the bezel inside the door handle
    • Remove the Phillips head screw inside the door handle
    • Remove the Phillips head screw inside the door pull
    • Remove the three Phillips head screws alongside the bottom of the door panel
    • Remove the Phillips head screw at the back of the door panel
    • Pull off the mirror base trim
    • With a putty knife pry off the door panel
    • Disconnect the door lock wiring harness
    • Disconnect the latch rod from the door handle
    • Disconnect the power window switch wiring harness
    • If any pins remain in the door, remove them with needle nose pliers
    • Reinstall those pins into the door panel
  2. Removing the Window Regulator (3:34 in the video)
    • Carefully pull back the water shield, avoiding tearing it
    • Remove the six 10mm nuts that hold the regulator to the door
    • Pull the window down partially by hand
    • Loosen the two 10mm nuts on the window track
    • Remove the window from the window track
    • Pull the window up by hand
    • Pull the window regulator partially out
    • Disconnect the window motor wiring harness
  3. Detaching the Window Motor from the Window Regulator (6:46 in the video)
    • Remove the three T25 Torx screws that hold the motor to the regulator
    • Detach the motor from the regulator
  4. Attaching the New Motor to the Regulator (7:24 in the video)
    • Line up the motor and regulator gears
    • Push the motor into place
    • Start the three screws by hand
    • Tighten the three T25 Torx screws
  5. Reattaching the Window Regulator (8:06 in the video)
    • Connect the window motor to its wiring harness
    • Connect the window switch to its wiring harness
    • Turn the regulator down slightly, using the window switch
    • Insert the regulator into the door
    • Put the regulator into place
    • Start all the nuts and bolts by hand
    • Tighten all the nuts and bolts
    • Move the regulator into place with the window switch
    • Disconnect the wiring harness from the window switch
    • Slide the window onto the window track
    • Tighten the 10mm nuts on the window track
    • Carefully put the water shield back into place
  6. Reinstalling the Door Panel (11:11 in the video)
    • Reconnect the wiring harness to the window switch
    • Check that the window regulator and motor function properly
    • Reconnect the door lock switch
    • Clip the latch rod to the door handle
    • Slide the door panel into place
    • Push the door panel locating tab into its hole
    • Push the pins in
    • Insert the Phillips screw into the door pull
    • Insert the Phillips screw into the door handle
    • Insert the three Phillips screws along the bottom of the door panel
    • Insert the Phillips screw at the back of the door panel
    • Push the mirror base trim back into place
    • Put the bezel back into the door handle
    • Put the bezel back into the door pull

Tools needed for replacement:

    Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • Door Panel Removal Tool
  • Flashlight
  • Putty Knife

  • Torx Drivers & Sockets

  • T30 Torx Driver

How-to Video:

(13:35 min)

Tools List:

    Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • Door Panel Removal Tool
  • Flashlight
  • Putty Knife

  • Torx Drivers & Sockets

  • T30 Torx Driver




Vehicle Fit

  • 1992-2013 Ford E150 Van Power Window Motor Front Pair
  • 1992-2013 Ford E250 Van Power Window Motor Front Pair
  • 1992-2013 Ford E350 Van Power Window Motor Front Pair
  • 2003-2013 Ford E450 Van Super Duty Power Window Motor Front Pair
  • 2003 Ford E550 Van Super Duty Power Window Motor Front Pair
  • 1991-1994 Ford Explorer Power Window Motor Rear Pair
$114.95
Save 51%
List: $235.96 Save: $121.01
Only 1 left in stock
Part #: 1AWMK00063

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est