Replaces
This part doesn’t fit a . Select from parts that fit.
Light Assembly Lifetime Warranty
Frequently bought together
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
The bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks!
In this video, we're going to show you removal and replacement of fog lights, as well as just changing the bulbs. It's a 2008 Dodge Ram. Same for 2002 to 2008, 1500, as well as the 2003 to 2009 2500 and 3500. You'll need new fog lights from 1AAuto.com, as well as a 10mm socket and ratchet.
You can access the back of your fog light pretty easily with the vehicle on the ground, but we're going to raise it up and just show you better underneath. If you're just looking to change the bulb, and for removal and installation, turn the bulb counterclockwise, pull it out, and you want to disconnect by pulling on the tab here and remove.
If you're just installing the bulb, reinstallation is just the reverse of that. Plug it back in. Put it in so it fits, and turn it to lock. You want to make sure you don't touch the glass part of the bulb when you're doing that, on the new bulb.
To remove a broken fog light, just remove these three screws. They're 10mm: here, here, and here. The light will come right out.
Reinstallation of the new light from 1AAuto.com, although we are just installing our old one, because it's in perfectly fine shape.
Put this side up in the first. Put it back in. Start the three bolts in. Tighten preliminarily. Check it from the front, and move it up and down if you like, and tighten up the bolts. Install the bulb as needed, and make sure it's plugged back into the harness. It's the same procedure for the driver's side.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
Tools used
Okay, friends. To get started on replacing our fog lights, it's gonna be easiest from under the front bumper. As you can see right along here, you can see the assembly, and, of course, you can see the wiring. We need to disconnect the wiring. I'm just gonna use a pocket screwdriver. Just kind of pull on these two tabs a little bit and then I should be able to pull this down. Take a look, make sure you don't see any funny colors, set that aside. Next, we're gonna remove our three 10-millimeter headed mounting bolts. Grab your fog light and remove it.
All right, friends. Now, it's time to install our brand new fog lamp assembly. Something that I wanna show you while it's out, is this area right here, is your adjuster. Let's go ahead and get this up inside here. Start in all three of your bolts and then we'll snug them up. Just gonna use a tiny bit of dielectric grease on this and we'll connect it in. Make sure it's clipped, give it a nice tug. Perfect. To adjust your foglight, just use a Phillips head, comes right through this slot right there. So, once your headlamps are properly adjusted, it'll be time to adjust your fog lamps. You'll notice on the driver side, the focal point is all the way at the bottom right now. I would like to bring it up so it meets up with approximately the bottom of the focal point of the headlight. Some fog lamps have an adjuster, others don't, the ones that do have an adjuster, you would just turn the adjustment to the left or to the right to adjust the beam up and down to where it needs to be. Now with your TRQ headlamps and fog lamps properly aligned, you can drive down the road safely.
