1999-2003 Dodge Durango 2WD Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS (Timken)

Part Details

  • Location: Front
  • Transmission/Drivetrain Type: 2 Wheel Drive
  • Brands: Timken

This part replaces:

  • HOLLANDER 538-01424A
  • TIMKEN HA599528
  • OE # 52009528

  • New


This replacement hub & bearing assembly is just what you need to get your vehicle in good working order again.


  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • Fits 6 Lug Wheel
  • Replaces dealer part number: 52009528
  • Direct replacement
  • Built to strict quality control standards
  • New wheel studs installed
  • Fits 2WD (Two Wheel Drive) Models only
  • Fits models with RWAL (Rear Wheel ABS) only

Note: This part is an authentic Timken brand product that is supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.


  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hub & bearings are all tested prior to shipping.

Fit Guaranteed

  • This hub & bearing will install just as your original does. You can use your existing hardware.
  • Save time and money with this direct fit hub bearing assembly. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.


  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

Lifetime Warranty

Effective June 23, 2014: This item is backed by a manufacturer's Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Step 1: Remove wheel.
    • While your car is still on the ground, use your 32mm socket to loosen the center hub nut.
    • Loosen your lug nuts and jack up the car.
    • Remove the lug nuts with your 19mm socket and ratchet.
    • Remove the wheel and set aside.
  2. Step 2: Remove the brakes
    • Remove the T47 torx bolts holding the calipers and the bracket.
    • Wire tie the caliper up and out of the way, set the bracket to the side.
    • Remove your rotor and set aside.
  3. Step 3: Remove axle
    • Remove the 14mm bolts securing the axle.
    • Use an axle puller or a light, but firm, tap with a small hammer on the axle to remove it.
  4. Step 4: Remove hub
    • Remove the three 22 mm bolts, using penetrating oil to help.
    • A breaker bar or piece of pipe on the end of your ratchet may be needed.
    • Remove the hub and clean the area with a wire brush.
  5. Step 5: Replace hub
    • Clean hub seating with a wire brush and add a little anti-seize grease.
    • Put position your new 1A Auto hub in its seating.
    • Put the three 22 mm bolts in place and tighten the nuts to 90 ft lbs.
    • Reinstall the axle and torque the 14 mm bolts to 60 ft lbs.
  6. Step 6: Put brakes and wheel back on
    • Refer to our other videos for more detailed instructions.
    • Remember to replace the lug nuts on in a star pattern.
    • Lug nuts tighten to 90-100 ft lbs
    • Hub nut is 175 ft lbs.
    • Make sure to check your brakes and steering before driving again.
    • Make sure to have the vehicle aligned.

How-to Video:

(12:36 min)

Tools List:

    Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 18mm Socket
  • 19mm Socket
  • 32mm Socket

  • Specialty Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Torx Drivers & Sockets

  • T47 Torx Socket

This part replaces:

  • HOLLANDER 538-01424A
  • TIMKEN HA599528
  • OE # 52009528

Vehicle Fit

  • 1997-2004 Dodge Dakota 2WD Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS (Timken)
  • 1999-2003 Dodge Durango 2WD Front Wheel Bearing & Hub Assembly for Models with Rear Wheel ABS (Timken)
Save 30%
List: $156.00 Save: $46.05
Part #: TKSHF00124

- Ships Same Day for orders placed by 5 P.M. ET


Check Shipping Rates
Brand #: HA599528

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!


hablamos Español:866-401-3393
For Orders Placed By 5pm Est