Replaces

1997-2003 Ford F150 Truck Front CV Axle Shaft Driver or Passenger Side (A1 Cardone)

Part Details

  • Brands: A1 Cardone

This part replaces:

  • OE # 5L3Z 3B436 A
  • HOLLANDER 447-02844
  • A1 CARDONE 66-2112

  • New

A1 CARDONE SELECT CV JOINT AXLE SHAFT (66-2112) LF = RF

This axle shaft is a new, aftermarket part. It is just what you need to get your vehicle in good working order!

Specifications:

  • Fits either the LH (Driver) or RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 5L3Z 3B436 A, 5L3Z3B436A
  • Brand New, not refurbished or rebuilt
  • Built to strict quality control standards
  • No core charge

Features & Benefits of each NEW CV (Constant Velocity) axle shaft:

  • 100% Neoprene Boots for excellent Ozone resistance. - Eliminates cracking; a leading cause for failure of CV boots
  • 3% moly grease. - Provides excellent high temperature and extreme pressure characteristics which extends the life of the joint
  • Axle nut supplied 100%. - If axle nut from the vehicle is worn or stripped there is no need to buy a separate axle nut because it is provided
  • Splines rolled 100%. - Guarantees proper installation of axle into mating hub and transmission eliminating installation hassle
  • Threads rolled 100%. - Guarantees proper installation of axle nut eliminating installation hassle

Note: This is for one axle shaft assembly.

Axle shafts may need replacing for a variety of different reasons. On vehicles that do heavy work or endure other extreme use you can actually break an axle or strip the splines or teeth. More often the CV joint wears out causing noises and vibration while accelerating or turning.

Lifetime Warranty

Effective June 23, 2014: This item is backed by a manufacturer's Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Remove the wheel
    • Remove the lug cap
    • Loosen the lug nuts.
    • Remove the cover and cotter pin from the hub nut and loosen the hub nut.
    • Loosen the seven 13 mm 12 point bolts securing the axle to the front drive.
  2. Disconnect the stabilizer link
    • Hit them with penetrating oil
    • Use a 14 mm socket and 9/16 socket on the bottom to remove the stabilizer link.
    • This might take a bit of elbow grease with hand tools, but it will come loose.
    • Use a hammer to drive out the stabilizer link.
  3. Remove the half shaft of the CV axle.
    • Use a large crow bar between the lug bolts to secure the axle while you remove the 13 mm 12 point bolts if you didn't loosen them earlier.
    • Remove the hub nut.
    • Give the axle a good tap with the hammer to break it loose from the steering knuckle.
    • Pull the axle out.
  4. Install the new half shaft of the CV axle
    • Install the grease fitting on the ball joint and fill with grease.
    • Put the new axle in and bolt in.
    • In a star pattern, torque the 13 mm 12 point bolts to 60 ft lbs.
  5. Install the new stabilizer link.
    • Thread the bushings and washers on the stabilizer bar and tighten the lock nuts down.
    • Jack up the suspension a bit and tighten the stabilizer link up to 15-17 ft lbs.
  6. Put your hub and lug nuts and wheel back on.
    • Put the hub nut on and pre-tighten but don't torque it.
    • Put the wheel and lug nuts back on
    • Lower the vehicle and torque the lug nuts in a star pattern to 100 ft lbs.
    • Torque the hub nut to 220 ft lbs.
    • Replace the cotter pin and cover on the hub nut.
    • Put the lug cover back on.

How-to Video:

(08:52 min)

Tools List:

    Materials, Fluids, and Supplies

  • Penetrating Oil

  • Ratchets & Related

  • Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 14mm Socket
  • 19mm Socket
  • 35mm Socket

  • Sockets - SAE

  • 9/16 Inch Socket

  • Specialty Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Punch



This part replaces:

  • OE # 5L3Z 3B436 A
  • HOLLANDER 447-02844
  • A1 CARDONE 66-2112

Vehicle Fit

  • 1997-2002 Ford Expedition Front CV Axle Shaft Driver or Passenger Side (A1 Cardone)
  • 2004 Ford F150 Heritage Truck Front CV Axle Shaft Driver or Passenger Side (A1 Cardone)
  • 1997-2003 Ford F150 Truck Front CV Axle Shaft Driver or Passenger Side (A1 Cardone)
  • 1997-1999 Ford Front CV Axle Shaft Driver or Passenger Side (A1 Cardone)
  • 1998-2002 Lincoln Navigator Front CV Axle Shaft Driver or Passenger Side (A1 Cardone)
$99.95
Save 78%
List: $459.98 Save: $360.03
Part #: CAACV00009

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates
A1 CARDONE
Brand #: 66-2112

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est