Replaces

2001-2010 Dodge Grand Caravan Lower Coolant Inlet Tube for V6 3.3L (without Engine Oil Cooler)

This part replaces:

  • DORMAN 626-304
  • OE # 4781608AB
  • OE # 4781608AC
  • OE # 4781608AA

  • New

Specifications:

  • Attaches To Timing Cover
  • Direct replacement for a weakened or leaking hose
  • Built to strict quality control standards
  • Does NOT fit models with Engine Oil Cooler

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Draining the Coolant (0:56)
    • Have a drain pan ready
    • Insert a tube to the drain
    • Turn the valve a quarter turn counterclockwise to remove it
    • Let the coolant drain
    • Remove the radiator cap to speed up the process
  2. Removing the Wheel (1:51)
    • Loosen the 21mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  3. Removing the Inner Wheel Well Panels (2:05)
    • Pull off the four pins in the wheel well with a flat blade screwdriver and a pair of pliers
    • Remove the two Phillips screws on the edge of the bumper cover
    • Remove the inner wheel well
    • Pull down the second panel to remove the pins
  4. Removing the Lower Coolant Tube (3:16)
    • Slide off the hose clamp from the radiator hose with a pair of pliers
    • Have a drain pan ready
    • Pry off the hose with a flat blade screwdriver
    • Let the fluid drain
    • Remove the 13mm bolt from the bracket
    • Remove the 13mm bolt from the water inlet housing
    • Pull the coolant tube down and out
    • Clean out any material on the housing and inlet
  5. Installing the New Lower Coolant Tube (5:33)
    • Coat the o-ring with motor oil
    • Insert the coolant tube into place
    • Preliminarily tighten the 13mm bolt to the inlet housing
    • Tighten the 13mm bolt to the bracket most of the way
    • Finish tightening the 13mm bolt to the inlet housing
    • Finish tightening the 13mm bolt to the bracket
    • Slide the hose clamp into place
  6. Installing the Inner Wheel Well Panels (7:22)
    • Push the inside panel into place and replace the clips
    • Push the wheel well panel into place and replace the four clips
    • Tighten the two Phillip screws to the edge of the bumper cover
  7. Reattaching the Wheel (8:04)
    • Slide the wheel into place
    • Start the 21mm lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
  8. Refilling the Coolant (8:26)
    • Push the radiator drain in a quarter of a turn to a vertical position
    • Turn the plug 90 degrees with pliers to close the valve
    • Refill the radiator with the correct 50/50 mixture until the radiator is topped off
    • Tighten the radiator cap
    • Refill the coolant reservoir to the max fill line
  9. Testing the Coolant (10:10)
    • Start the vehicle
    • Circulate the coolant by turning on the front and rear heat
    • Check the coolant level after 10 minutes of driving
    • For the first few days of driving, check to make sure the coolant level is between the max/min fill line

Tools needed for replacement:

    General Tools

  • Drain Pan
  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rubber Vacuum Hose

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 13mm Socket

How-to Video:

(11:09 min)

Tools List:

    General Tools

  • Drain Pan
  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rubber Vacuum Hose

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 13mm Socket



This part replaces:

  • DORMAN 626-304
  • OE # 4781608AB
  • OE # 4781608AC
  • OE # 4781608AA

Vehicle Fit

  • 2001-2010 Chrysler Town & Country Lower Coolant Inlet Tube for V6 3.3L (without Engine Oil Cooler)
  • 2001-2010 Chrysler Town & Country Lower Coolant Inlet Tube for V6 3.8L (without Engine Oil Cooler)
  • 2001-2003 Chrysler Voyager Lower Coolant Inlet Tube for V6 3.3L (without Engine Oil Cooler)
  • 2001-2007 Dodge Caravan Lower Coolant Inlet Tube for V6 3.3L (without Engine Oil Cooler)
  • 2001-2010 Dodge Grand Caravan Lower Coolant Inlet Tube for V6 3.8L (without Engine Oil Cooler)
  • 2001-2010 Dodge Grand Caravan Lower Coolant Inlet Tube for V6 3.3L (without Engine Oil Cooler)
$45.45
Only 3 left in stock
Part #: 1AEMX00106

Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est