Replaces

1998-2001 Mazda B2500 Truck 2 Wheel Drive Front Upper Control Arm with Ball Joint for Coil Spring Suspension Passenger Side

This part replaces:

  • DORMAN 520-238
  • HOLLANDER 511-01064R
  • OE # 3L5Z3084DA, 6L5Z3084BA, 1F7134211, MCS0E30
  • Moog K80052

  • New

This replacement front upper control arm is just what you need to bring back the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • RH (Passenger Side) FRONT UPPER
  • Complete assembly
    • Includes ball joint and bushings
  • Direct replacement
  • Built to strict quality control standards
  • Fits 2WD (Two Wheel Drive) Models only
  • Fits models with Standard Duty Coil Suspension only

Worn ball joints can cause excessive front tire wear, popping or creaking in the front end, extra play in the steering system, and pose a serious safety concern. Replace loose or worn ball joints with our quality replacement.

One way to diagnose a loose, or warn ball joint, is to jack the car up, so the wheel is off of the ground, then have someone try to move the wheel in and out. While they are moving the wheel check the ball joint for play, if it is moving you probably need to replace it.

Remember whenever you are replacing any front end or steering components you should have your vehicle professionally aligned as soon as possible. This will ensure proper tracking and even tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Remove the wheel (1:10)
    • Loosen the lug nuts
    • Raise and secure the vehicle
    • Remove the lug nuts and set the wheel aside.
    • Put the wheel under the vehicle for added security in the event of a jack failure.
  2. Remove the brakes (2:00)
    • Remove the 13 mm sockets anchoring the caliper.
    • Wire tie the caliper up out of the way.
    • Use a 15mm socket to remove the caliper bracket
    • Remove the rotor
    • Remove the dust shield with your 8 mm socket and ratchet
  3. Remove the outer tie rod (3:00)
    • Use your pliers to remove the cotter pin from the tie rod
    • Remove the nut with your 21 mm socket and ratchet
    • Pull apart the tie rod with a tie rod puller.
    • Use a paint marker to mark where the top nut on the tie rod is.
    • Use two adjustable wrenches to remove the tie rod.
  4. Install the new tie rod (6:15)
    • Apply a little loctite to the inner tie rod
    • Screw on the outer tie rod to the inner tie rod up to your paint marker mark.
    • Fill the dust boot with grease
    • Reassemble the tie rod end, replacing the nut and cotter pin.
    • Reassemble the brakes and wheel.
    • See our other videos for more detailed instructions.

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Wire Ties
  • Liquid Thread Locker
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Lug Wrench
  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 8mm Socket
  • 15mm Socket
  • 21mm Socket

  • Specialty Tools

  • Tie Rod Puller

How-to Video:

(10:34 min)

Tools List:

    General Tools

  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Wire Ties
  • Liquid Thread Locker
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Lug Wrench
  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 8mm Socket
  • 15mm Socket
  • 21mm Socket

  • Specialty Tools

  • Tie Rod Puller



This part replaces:

  • DORMAN 520-238
  • HOLLANDER 511-01064R
  • OE # 3L5Z3084DA, 6L5Z3084BA, 1F7134211, MCS0E30
  • Moog K80052

Vehicle Fit

  • 1998-2011 Ford Ranger 2 Wheel Drive Front Upper Control Arm with Ball Joint for Coil Spring Suspension Passenger Side
  • 2001-2009 Mazda B2300 Truck 2 Wheel Drive Front Upper Control Arm with Ball Joint for Coil Spring Suspension Passenger Side
  • 1998-2001 Mazda B2500 Truck 2 Wheel Drive Front Upper Control Arm with Ball Joint for Coil Spring Suspension Passenger Side
  • 1998-2007 Mazda B3000 Truck 2 Wheel Drive Front Upper Control Arm with Ball Joint for Coil Spring Suspension Passenger Side
  • 1998-2009 Mazda B4000 Truck 2 Wheel Drive Front Upper Control Arm with Ball Joint for Coil Spring Suspension Passenger Side
$49.95
Save 65%
List: $143.96 Save: $94.01
Part #: 1ASFU00108

Out of Stock

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est