Replaces

2010-2010 Ford F150 Truck Front Upper Control Arm with Ball Joint Pair (Built Before 10/20/09 Production Date) Motorcraft MCSOE28, MCSOE29

Part Details

  • Location: Upper
  • Front / Rear Location: Front
  • Quantity: Pair

This part replaces:

  • Motorcraft MCSOE28, MCSOE29
  • OE # 4L3Z3084AA
  • OE # 7L1Z3084A
  • OE # 4L3Z3084AB
  • OE # 7L1Z3085A
  • OE # 6L3Z3085AL
  • OE # 4L3Z3085AA
  • OE # 9L3Z3085A
  • OE # 4L3Z3085AB
  • Motorcraft MCSOE29
  • Motorcraft MCSOE28

  • New

Specifications:

  • Brand New Motorcraft Control Arms
  • Comes as a Pair
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT UPPER
  • Control arms include ball joints & bushings
  • Built to strict quality control standards

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

    It's recommended to seek an alignment after finishing this repair

  1. Removing the Wheel (0:48)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 21mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. Loosening the Outer Tie Rod (1:22)
    • Turn the wheel
    • Remove the 21mm nut from the outer tie rod
    • Leave the 21mm nut on a couple threads
    • Hammer the knuckle until the outer tie rod loosens
    • Set the outer tie rod off to the side
  3. Loosening the Strut (1:50)
    • Remove the 18mm nut below the sway bar link with an 18mm wrench and an 8mm socket and ratchet
    • Hold the 20mm nut on the bottom of the strut with a 27mm socket and ratchet
    • Loosen the 30mm nut on the bottom of the strut with a breaker bar and piece of pipe
    • Remove two of the 15mm nuts on the top of the strut
    • Leave the other 15mm nut on the top of the strut by a few threads
  4. Loosening the Axle (3:03)
    • Remove the hub nut cap with a pair of pliers
    • Remove the 13mm hub nut
    • Replace the 13mm nut by a few threads and tap the nut with a hammer to push the axle through
    • Remove the nut
    • Have an assistant hold the brakes
    • Remove the 12mm bolts from the axle with a 12mm 12-point socket
  5. Removing the Axle (4:12)
    • Remove the 21mm nut from the bottom of the upper control arm
    • Thread the 21mm nut on
    • Loosen the upper control arm with a hammer
    • Remove the nut
    • Manuever the wheel knuckle to the side without straining the brake lines
    • Remove the axle
  6. Removing the Strut (6:00)
    • Jack up underneath the control arm
    • Remove the bolt on the bottom of the strut
    • Pry the strut out and remove it
  7. Removing the Control Arm (6:30)
    • Remove the nuts on either side of the upper control arm with a 21mm wrench and 21mm socket and ratchet
    • Leave the 21mm bolts on by a thread
    • Hold the upper control arm in place and remove the bolts
    • Remove the control arm
    • Step 8: Installing the Upper Control Arm [7:26]
    • Insert the upper control arm into place
    • Insert the 21mm control arm bolts in place
    • Preliminarily tighten the 21mm nuts
  8. Installing the Strut (8:00)
    • Insert the strut into place
    • Insert the 15mm nuts to the strut to hold it in place
    • Pry the strut into the lower control arm
    • Insert the bolt into the strut
    • Preliminarily tighten the nut on the bolt
    • Tighten the 15mm nuts
  9. Reinstalling the Axle (7:49)
    • Insert the axle into place
    • Insert the upper control arm into the wheel knuckle
    • Tighten the 21mm nut
    • Tighten the 12mm bolts into the axle
    • Torque the 12mm nuts to 60 foot-pounds in a crossing pattern
    • Tighten 13mm hub nut
    • Torque the hub nut to 20 foot-pounds
    • Tap the hub nut cap into place
    • Re-clip and realign any lines that may have come undone
  10. Reinstalling the Outer Tie Rod (9:27)
    • Push the outer tie-rod up through the wheel knuckle
    • Replace the 21mm nut
    • Torque the 21mm nut to 111 foot-pounds
    • Tighten the bolt on the upper control arm
    • Torque the upper control arm 21mm nut to 111 foot-pounds
    • Tighten the 18mm nut to the sway bar link
    • Jack underneath the control arm
    • Torque the lower strut bolt to 150 foot-pounds
  11. Reattaching the Wheel (10:16)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 120 foot-pounds in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • A Piece of Pipe (for leverage)

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 27mm socket
  • 8mm Socket
  • 12mm 12-Point Socket
  • 30mm Socket
  • 15mm Socket
  • 13mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(12:57 min)

Tools List:

    General Tools

  • Floor Jack
  • Jack Stands
  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • A Piece of Pipe (for leverage)

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 27mm socket
  • 8mm Socket
  • 12mm 12-Point Socket
  • 30mm Socket
  • 15mm Socket
  • 13mm Socket



This part replaces:

  • Motorcraft MCSOE28, MCSOE29
  • OE # 4L3Z3084AA
  • OE # 7L1Z3084A
  • OE # 4L3Z3084AB
  • OE # 7L1Z3085A
  • OE # 6L3Z3085AL
  • OE # 4L3Z3085AA
  • OE # 9L3Z3085A
  • OE # 4L3Z3085AB
  • Motorcraft MCSOE29
  • Motorcraft MCSOE28

Vehicle Fit

  • 2004 Ford F150 Truck Front Upper Control Arm with Ball Joint Pair (excluding Heritage Models) Motorcraft MCSOE28, MCSOE29
  • 2005-2009 Ford F150 Truck Front Upper Control Arm with Ball Joint Pair Motorcraft MCSOE28, MCSOE29
  • 2010 Ford F150 Truck Front Upper Control Arm with Ball Joint Pair (Built Before 10/20/09 Production Date) Motorcraft MCSOE28, MCSOE29
  • 2006-2008 Lincoln Mark LT Front Upper Control Arm with Ball Joint Pair Motorcraft MCSOE28, MCSOE29
$259.95
Only 3 left in stock
Part #: MCSFK00003

Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates
MOTORCRAFT
Brand #: MCSOE28, MCSOE29

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est