Replaces

1998-2002 Lincoln Navigator 4WD Front Upper Control Arm with Ball Joint Driver Side (excluding Air Suspension)

Part Details

  • Location: Upper
  • Front / Rear Location: Front
  • Side Location: Driver Side

This part replaces:

  • HOLLANDER 511-01023BL
  • DORMAN 520-215
  • OE # 5L3Z3085C
  • OE # F75Z3085BA
  • OE # XL3Z3085BA

  • New

This replacement front upper control arm is just what you need to bring back the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Fits LH (Driver Side) FRONT UPPER
  • Includes new ball joint and inner bushings
  • Replaces dealer part numbers: 5L3Z-3085-C, 5L3Z3085C, F75Z-3085-BA, F75Z3085BA, XL3Z-3085-BA, XL3Z3085BA
  • Control arm is new, not remanufactured or refurbished

Worn ball joints or loose rear bushings can cause excessive front tire wear, popping or creaking in the front end, extra play in the steering system, and pose a serious safety concern. Replace that heavily rusted, rotted, or damaged front upper control arm with the loose bushings or worn ball joints with our high quality all in one replacement.

One way to diagnose a loose, or warn ball joint on a control arm, is to jack the car up, so the wheel is off of the ground, then have someone try to move the wheel in and out. While they are moving the wheel check the ball joint and bushings for play, if it is moving you probably need to replace it.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Remove the Wheel (1:59)
    • Pull off the center cap
    • Loosen the lug nuts
    • Remove the cotter pin and loosen the 35mm hub nut
    • Loosen the seven 13mm 12-point bolts that hold the axle to the front drive
    • Raise and secure the car
    • Remove the wheel
  2. Loosen the Torsion Bar (2:54)
    • Spray the torsion bar with spray paint and loosen the torsion bar tension bolt with an 18mm bolt
  3. Remove the Tie Rod (3:45)
    • Use a pair of pliers to remove the cotter pin
    • Remove the nut at the end of the tie rod
    • Use a tie rod puller to separate the tie rod
  4. Remove the stabilizer links (5:25)
    • Use a 9/16 wrench to secure the bottom and a 14 mm socket to unbolt the stabilizer link
    • Use a hammer and punch to remove the stabilizer link
  5. Pull the Axle from the CV Joint (6:52)
    • Unbolt the seven bolts, using a pry bar to keep the hub from rotating
    • Remove the hub nut using a 35 mm socket
    • Give the axle a tap with a hammer and pull the axle out
  6. Remove the Ball Joint (9:00)
    • Use a jack and wood plank or two to lift the control arm and relieve tension from the ball joint
    • Unbolt the the ball joint using a breaker bar and 27mm socket
    • Use a ball joint removal tool to pull the ball joint apart
    • With a ball joint press, remove the ball joint completely
    • See Part Two for reassembly

Tools needed for replacement:

    General Tools

  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Ball Joint Press
  • Tie Rod Puller


How-to Video:

(13:53 min)

Tools List:

    General Tools

  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Block of Wood
  • Marker / Writing Utensil
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • Ball Joint Press
  • Tie Rod Puller



This part replaces:

  • HOLLANDER 511-01023BL
  • DORMAN 520-215
  • OE # 5L3Z3085C
  • OE # F75Z3085BA
  • OE # XL3Z3085BA

Vehicle Fit

  • 1997-2002 Ford Expedition 4WD Front Upper Control Arm with Ball Joint Driver Side (excluding Air Suspension)
  • 2004 Ford F150 Heritage Truck 4WD Front Upper Control Arm with Ball Joint Driver Side
  • 1997-2003 Ford F150 Truck 4WD Front Upper Control Arm with Ball Joint Driver Side
  • 1997-1999 Ford F250 Light Duty Truck 4WD Front Upper Control Arm with Ball Joint Driver Side
  • 1998-2002 Lincoln Navigator 4WD Front Upper Control Arm with Ball Joint Driver Side (excluding Air Suspension)
$46.95
Save 49%
List: $91.98 Save: $45.03
Part #: 1ASFU00021

Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est