Replaces

2003-2007 Cadillac CTS Front for Models with 5 Lug Wheels Wheel Bearing & Hub Assembly Pair

Part Details

  • Front / Rear Location: Front
  • Quantity: Pair

  • New

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • 3 Bolt Triangular Flanges
  • Fits 5 Lug Wheels
  • Replaces dealer part number: 12413071
  • Studs already installed
  • Built to strict quality control standards
  • Built in ABS sensor with correct plug configuration
  • Fit RWD (Rear Wheel Drive) Models only
    • Do NOT fit V-Series with 6 Stud Hub
    • Do NOT fit AWD (All Wheel Drive) Models

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hubs & bearings are all tested prior to shipping.

Fit Guaranteed

  • These hub & bearing sets will install just as your originals do. You can use your existing hardware.
  • Save time and money with direct fit hub bearing assemblies. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

2 Year Warranty

This item is backed by a 2 Year Warranty. In the event this item should fail during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Wheel (0:30)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. Removing the Rotor (2:20)
    • Remove the T30 Torx bolt from the rotors
    • Remove the two 18mm bolts holding the caliper bracket to the spindle
    • Secure the caliper with a bungee chord
    • Remove the rotor
  3. Removing the Hub (3:20)
    • Disconnect the ABS connector from the backing plate
    • Disconnect the ABS sensor wiring harness
    • Remove the three 18mm bolts from the spindle
    • Remove the 18mm bolt from the back of the spindle
    • Hammer out the hub
    • Remove the hub and the dust shield
    • Tap the back of the ABS sensor out of the spindle with a flat blade screwdriver and hammer
  4. Installing the Hub (5:45)
    • Clean the bore of the spindle with a wire brush
    • Line up the dust shield
    • Insert the hub into place
    • Line up the top bolt
    • Hand-tighten the other two bolts
    • Torque the wheel hub bolts to 100 foot-pounds
    • Reconnect the ABS harness container
    • Reconnect the ABS wiring harness
    • Apply a thin coat of brake grease to the hub
  5. Installing the Rotor (7:40)
    • Insert the rotor into place
    • Thread the T30 Torx bolt into place
    • Lower the brake caliper to the rotor
    • Start the two 18mm bolts to the brake caliper
    • Torque the bolts to 96 foot-pounds
  6. Reattaching the Wheel (8:40)
    • Slide the wheel into place
    • Start the 19mm lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Anti-Seize Grease
  • Bungee Chord

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 18mm Socket
  • 19mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver

  • Wrenches - Metric

  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(10:32 min)

Tools List:

    General Tools

  • Jack Stands
  • Hammer
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Anti-Seize Grease
  • Bungee Chord

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 18mm Socket
  • 19mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver

  • Wrenches - Metric

  • 18mm Wrench




Vehicle Fit

  • 2003-2007 Cadillac CTS Front for Models with 5 Lug Wheels Wheel Bearing & Hub Assembly Pair
  • 2005-2011 Cadillac STS Front for Models with 5 Lug Wheels Wheel Bearing & Hub Assembly Rear Wheel Drive Pair
$ 82.95
Save 93%
List: $1,213.36 Save: $1,130.41
Part #: 1ASHS00610

Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY M-F
For Orders Placed By 5pm Est