Brake Rotors at 1A Auto
What are brake rotors and where are they located?
Brake rotors, also commonly referred to as brake discs, are major components in a disc brake system. A disc brake system consists of brake calipers, pads, and rotors. The rotors bolt onto the wheel hubs or axles, and spin at the same rate as the wheels. When you press the brake pedal, hydraulic pressure is transmitted to the caliper, which acts as a clamping device pressing the brake pads against each side of the rotor. The friction that this creates is what allows the vehicle to slow to a stop.
Most cars and trucks today have four brake discs, one for each wheel in the front of the vehicle and one for each wheel in the rear of the vehicle. However, a lot of vehicles have rear drums instead of brake discs. In this case, the vehicle will have two front brake rotors and two rear brake drums.
Types of brake rotors
The vast majority of automotive brake rotors are made from cast iron; however there are many different variations in the design and appearance. Let’s go over the most common types of brake discs used in today’s cars and trucks.
Solid and Vented Brake Rotors
The term “solid rotor” refers to a disc that has no vents. This type of brake rotor was the standard for many years, and can still be found on some vehicles today (although more often as a rear brake rotor). The downside to this rotor is its inability to efficiently dissipate the heat created from the braking process. Heat is the enemy of proper braking, as excessive heat can cause the brake pads to lose their friction capability, resulting in brake fade.
Vented brake discs were developed to combat this issue; these brake rotors have cooling fins placed in between the two sides of the disc. These fins allow for air to flow through the disc aiding in the cooling process, resulting in reduced brake fade and better heat dissipation. Vented discs are now widely used, and are the most common type of brake rotor found in the front of modern vehicles.
Drilled and Slotted Brake Rotors
Inspired by racing and high performance, the evolution of brake rotor technology has produced drilled rotors and slotted rotors. Some vehicles can come from the factory with drilled brake rotors. Both versions have the added benefit of increased heat dissipation, as well as allow for water and gasses to escape from between the brake pads and the rotor surface, although both are not without their flaws.
Drilled brake rotors have a series of holes drilled through the rotor surface. This means there is actually less surface material for the brake pad to grab. Drilled rotors can also be prone to cracking since they are inherently weaker than a brake rotor with a solid face. Slotted brake rotors are also known to wear brake pads down much more quickly than other rotor types as the slots tend to shave the brake pad surface. Another downside to each of these types of brake rotors is that mud and dirt can lodge inside the slots or holes. For these reasons, they are not recommended for use in off-road applications.
Hub and Brake Rotor Assemblies
At one time, the majority of cars and trucks had the wheel hub and brake disc incorporated together. This type of rotor can still be found today, specifically on two wheel drive pickup trucks and vans. When replacing this style of brake rotor, the wheel bearings must be removed from the original brake rotors and pressed into the new ones.
Brake Rotors with Parking Drum Brakes
Many vehicles today with rear disc brakes use emergency or parking brake shoes. The brake rotor in these applications is a rotor / drum combination.
How do I know if my brake rotors need to be replaced?
Brake rotors can be resurfaced or machined as long as there is enough material to do so. All brake rotors have a discard thickness determined by the manufacturer, which is the thinnest a rotor can be machined to before they are deemed unsafe and must be replaced (this information is often stamped into the edge or the rotor itself). It is recommended to measure the thickness every time you inspect the brakes or replace the brake pads, as well as to regularly inspect the brake rotor for any signs of cracking, rust, corrosion or uneven disc surface. Pedal pulsation is caused by thickness variations of the disc; this is often the result of brake pad friction material adhering to the surface of the rotor. At one time it was very common to resurface brake rotors, however today it is often more cost effective to replace the rotors rather than machining them.
Can I replace a brake rotor myself?
Do-it-yourselfers with some prior brake experience can replace their own brake rotors. You will need to raise and secure the vehicle. Then you can remove the wheel and tire and unbolt the caliper. Then unbolt the caliper bracket and pry off the brake pads. The rotor should simply slide off. If you have any issues with pulling the rotor off, sometimes you can threat a lug nut and strike the hub area of the rotor with a ball end of a ball peen hammer.
We recommend cleaning the new rotor with brake parts cleaner before installing it. Then slide the rotor on and thread a lug nut to hold it in place. Insert the caliper bracket into place. Start the bolt by hand and then torque the bolts to your vehicle's recommended specifications. Then place an old pad into the caliper and use a large C-clamp to reset the pistons. Insert the pads into the bracket and then place the caliper on. Thread the caliper bolts by hand and torque them to your vehicle's recommended specifications.Once the wheel and tire are fitted securely to the vehicle, and the vehicle is back on the ground, you’ll want to pump the brake pedal repeatedly until it feels firm—that helps to reset the pistons. Then test your brakes at low speed before road testing the vehicle.