Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
NOTE: It is necessary to reuse your original hardware, as new hardware is not included with this item.
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Item Condition:
New
Attention California Customers:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the lower grille on this 2012 Chevy Traverse. The items you'll need for that are a flat blade screw driver, a pair of pliers, 7mm and 10mm sockets and ratchet and a T20 Torx bit.
You want to start off by removing the series of clips in the shroud. To remove these clips, just pry up the center and pull the center out and the bottom just pops right out. Another option is pry up the center and then use these pliers to just pull the center out, and then, again, the button just pops right off. Pull up the ends of your weatherstrip, and now, that shroud should pull right up and off. Next, you want to remove these series of T20 bolts along the top of your bumper and we're just going to fast forward as Don removes these. In your wheel-well, there's a 7mm bolt right here. Just go ahead and remove that, and we'll fast forward as Don does this, and you want to do this on both sides of the vehicle. Now, you want to remove these two T20s in the wheel-well, and then, down here, you want to remove these series of T20s, as well as this 10mm bolt right here. You want to do the same thing on the other side as well. With the help from someone else .it's not necessary but it definitely does help ., you just want to pull the bumper cover out, and you want to start by pulling it out from the sides of the fender and then pulling it straight out. Then you want to disconnect the harnesses on the back of your lights and just push the tab and pull the harnesses free.
On the back of your bumper cover, you'll see right here on your grille, you just push those tabs in. You want to do that for each one and then pry it up over those red hooks and we'll fast forward as Don and Mike do this. Once you've got all of them, the grille will pull right off.
Take your new grille and push it down into place and just go around and make sure that each clip has re-clipped.
To re-install your bumper cover, again, it helps to have two people here. First, reconnect your lights by plugging the harnesses back in, and then, line up your bumper cover and push it into place, and just hit it in the sides to reactive the clips. We'll just fast forward here as Don replaces the bolts along the top. Put the shroud back in place and re-clip your weatherstrip into it and then just replace those clips. To re-install these clips, you want to pull up the center, and then, you want to just push them into place and then you just push the center down to lock. We'll just fast forward as Don does the rest of these, and also, replaces the T20s underneath the bumper as well as that 7mm bolt in the wheel-well and the 10mm bolt underneath the bumper. Then, replace those T20s in the wheel-well.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
