Replaces

2006 Dodge Ram 1500 Truck Wheel Hub & Bearing Pair with CERAMIC Brake Pads & Rotors Set Front - 1ABMS00037

Part Details

  • Location: Front

This part replaces:

  • OE # 52070323AG
  • OE # 52010080AC
  • OE # 52070323AB
  • OE # 52010080AB
  • OE # 52070323AA
  • OE # 52010080AE
  • OE # 52010080AA
  • OE # 52070323AH
  • OE # 5083204AA
  • HOLLANDER 538-01579

  • New

This front wheel bearing/hub assembly, brake rotor, & brake pad set is just what you need to get your vehicle in good stopping order again!

Brake Pad Specifications:

  • Fits FRONT Rotors
  • 4 Piece Brake Pad Set
  • No core charge
  • Includes shims
  • Professional Grade Ceramic Enhanced Disc Brake Pads

Brake Rotor Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • Fit 5 Stud Wheels
  • 13.2" (336mm) Diameter

Wheel Bearing & Hub Assembly Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • 3 Bolt Flanges
  • Fits 5 Lug Wheels
  • Studs already installed
  • Include ABS sensors
  • Fits models with 4 Wheel ABS (Anti-Lock Brakes) only
    • Does NOT fit models with RWAL (Rear Wheel ABS)

This wheel bearing/hub assembly, brake rotor, & brake pad set makes great replacements and has good value over the price of dealer parts.

2 Year Warranty

This item is backed by a 2 Year Warranty. In the event this item should fail during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Remove the wheel and tire (1:13 in the video)
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel.
  2. Remove Caliper (1:40 in the video)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your socket wrench to remove the caliper bolts.
    • Use a wire tie to help prevent stress on the caliper.
    • Use your socket to remove the brackets.
  3. Remove brake disk (3:00 in the video)
    • Take care not to touch the rotor, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. Remove Hub (3:16 in the video)
    • Use a 35mm socket to remove the hub nut.
    • Give the axle a slight tap with a hammer to loosen it.
    • Use a pry bar to remove the axle.
    • Remove the 3 bolts securing the hub using your 18mm socket and extension and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Disconnect your ABS sensor.
    • Use a rubber mallet to break your hub free, and work around the flange with the hammer to pull it off.
    • Remove the hub and shield.
    • Clean up any corrosion with a wire brush.
  5. Install new hub (9:26 in the video)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Put the three 18 mm bolts in place and tighten the nuts to 100 ft lbs.
    • Reinstall the ABS harness.
    • Replace the axle.
    • Tighten but don't torque the lug nut.
  6. Put brakes and wheel back on (11:40 in the video)
    • Remember to replace the lug nuts on in a star pattern.
    • Lug nuts tighten to 120 ft lbs
    • Hub nut is 185 ft lbs.
    • Make sure to check your brakes and steering before driving again.
    • Make sure to pump the brakes and seat your rotors.

Tools needed for replacement:

    Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket

  • Sockets - SAE

  • 13/16 Inch Socket
  • 7/8 Inch Socket

  • Specialty Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

How-to Video:

(13:39 min)

Tools List:

    Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket

  • Sockets - SAE

  • 13/16 Inch Socket
  • 7/8 Inch Socket

  • Specialty Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Wire Brush



This part replaces:

  • OE # 52070323AG
  • OE # 52010080AC
  • OE # 52070323AB
  • OE # 52010080AB
  • OE # 52070323AA
  • OE # 52010080AE
  • OE # 52010080AA
  • OE # 52070323AH
  • OE # 5083204AA
  • HOLLANDER 538-01579

Vehicle Fit

  • 2006 Dodge Ram 1500 Truck SLT Front 2 Wheel Drive Wheel Hub & Bearing Pair with CERAMIC Brake Pads & Rotors Set for V6 3.7L with 4 Wheel ABS (excluding Mega Cab)
  • 2006 Dodge Ram 1500 Truck SLT 2 Wheel Drive Front Wheel Hub & Bearing Pair with CERAMIC Brake Pads & Rotors Set for V8 4.7L with 4 Wheel ABS (excluding Mega Cab)
$215.45
Only 4 left in stock
Part #: 1ABMS00037

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est