Replaces

2002-2006 Nissan Altima Smooth Black Exterior Door Handle Front Pair

Part Details

  • Location: Front
  • Quantity: Pair
  • Colors: Black

This part replaces:

  • OE # 80607-8J009,80606-8J009

  • New

These replacement door handles are just what you need to get your vehicle in good looking form again!

Specifications:

  • Come as a PAIR
    • Fits both the LH (Driver Side) & RH (Passenger Side) FRONT OUTER
  • Smooth Black Finish
    • Can be painted by buyer to any color desired or installed as is
  • Replaces dealer part numbers: 80606-8J009, 80607-8J009, 806068J009, 806078J009
  • Durable construction
  • Direct replacements
  • LH (Driver Side) Handle does NOT include Lock Cylinder
    • Buyer will need to reuse old Lock Cylinder
  • RH (Passenger Side) Handle does NOT have key cylinder hole

These exterior door handles are great replacements and have good cost savings over dealer units.

Lifetime Warranty

Effective June 23, 2014: This item is backed by a manufacturer's Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Door Panel
    • Pry off the screw cap inside the door pull with a flat blade screwdriver
    • Remove the Phillips head screw inside the door pull
    • Pry off the window switch panel with a flat blade screwdriver
    • Disconnect the wiring harnesses from the switch panel
    • Pry off the window base trim panel with a flat blade screwdriver
    • Pry off the screw cap inside the door handle with a flat blade screwdriver
    • Remove the Phillips screw inside the door handle
    • Remove the Phillips screw behind the door pull
    • Pull off the courtesy light
    • Disconnect the courtesy light from its wiring harness
    • Pry the door panel off by hand
    • Lift the door panel up and off
    • Disconnect the cables from the inner door handle
    • Disconnect the wiring harness from the door panel
  2. Removing the Regulator Panel
    • Pull the wiring harnesses out of their clips
    • Peel off the two rubber covers with a razor blade
    • Connect the switch panel to its wiring harness
    • Turn the ignition on
    • Raise the window with the switch
    • Remove the two 10mm bolts from the window regulator
    • Pull the window out by hand
    • Disconnect the window switch from the inner door panel
    • Remove the nine 10mm bolts from the door panel
    • Pull off the regulator panel
  3. Removing the Outer Door Handle
    • Undo the clips for the outer door handle rods
    • Pull the rods out of the outer door handle
    • Remove the small plastic cover from the door by hand
    • Remove the two 10mm bolts from the door handle
    • Pull the door lock wiring harness out of its clip
    • Push the outer door handle out of the door
    • Remove the 10mm bolt that holds the lock to the outer door handle
  4. Installing the New Outer Door Handle
    • Paint the new door handle to the desired color
    • Attach the lock to the new outer door handle
    • Insert the 10mm bolt into the door lock
    • Feed the door handle into the door
    • Clip the rods onto the door handle
    • Insert the two 10mm bolts into the new outer door handle
  5. Reinstalling the Regulator Panel
    • Put the regulator panel into place
    • Insert the nine 10mm bolts into the regulator panel
    • Slide the window into the door by hand
    • Replace the small plastic cover
    • Insert the two 10mm bolts into the window regulator
    • Put on the two rubber covers
    • Reconnect the wiring harnesses and push them into their clips
  6. Reinstalling the Door Panel
    • Put the door panel into place
    • Connect the wiring harness to the door panel
    • Clip the two cables to the inner door handle
    • Pull the wiring harnesses through the door panel cavity
    • Put the door panel into place
    • Push in the door panel clips
    • Connect the courtesy light to the wiring harness
    • Push the courtesy light in to place
    • Insert the Phillips screw inside the door handle
    • Push in the screw cap inside the door handle
    • Insert the Phillips screw behind the door pull
    • Connect the wiring harnesses to the window switch panel
    • Insert the Phillips head screw into the door pull
    • Push in the screw cap inside the door pull
    • Push on the mirror base trim

How-to Video:

(10:18 min)

Tools List:

    Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Specialty Tools

  • Razor Blade / Gasket Scraper



This part replaces:

  • OE # 80607-8J009,80606-8J009

Vehicle Fit

  • 2002-2006 Nissan Altima Smooth Black Exterior Door Handle Front Pair
$50.45
Save 46%
List: $93.00 Save: $42.55
Part #: 1ADHS00379

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est