Replaces

2001-2001 Ford Taurus Electric Fuel Pump and Sending Unit Module for V6 3.0L (excluding Flex Fuel) (Motorcraft)

This part replaces:

  • Motorcraft PFS196
  • OE # 1F1Z9H307GB

  • New

MOTORCRAFT FUEL PUMP ASSEMBLY: PFS196

This Fuel Pump is a FORD original equipment part! It is the same part that you would receive if you purchased it from your local Ford dealer!

This electric fuel pump and sender features the following specifications:

  • Brand NEW Ford/Motorcraft part
  • Fuel tank mounted
  • Includes:
    • Fuel Pump
    • Sending Unit
    • Hanger Assembly
    • Float
    • Strainer
  • Outlets: 2
  • Rheostat Range: 15-160 Ohms
  • Correct electrical connector
  • Replaces dealer part numbers: 1F1Z9H307GA, 1F1Z 9H 307 GA, 1F1Z9H307GB, 1F1Z 9H 307 GB, PFS 196, PFS196
  • Direct replacement
  • Built to strict quality control standards
    • Note: Does not include Lock Ring And Gasket

This electric fuel pump is a great replacement and has good cost savings over a dealer unit.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Fuel Pump Relay (0:44 in the video)
    • Start the engine
    • Remove the fuel pump relay from the fuse box
    • Let the engine stall out
    • Turn the engine off
  2. Disconnecting the Fuel Lines (1:04 in the video)
    • Jack the vehicle as high as possible
    • Disconnect the two fuel lines from the fuel filter
    • Place a drip pan underneath the fuel filter and pull the fuel lines free
    • Let the hoses drain
    • Release the hose clamps from the fuel tank filler tubes, let them slide back, and pry up the yellow clip
    • Remove the fuel line hose with penetrating oil
    • Remove the additional fuel line fittings and hoses
  3. Removing the Fuel Tank (4:22 in the video)
    • Disconnect the fuel pump electrical connector with a flat blade screwdriver
    • Place a block of wood on a jack and jack up the gas tank
    • Remove the 13mm bolts holding in the gas tank straps with an extension or impact wrench
    • Pull back the gas tank strap
    • Remove the pin with a flat blade screwdriver or pliers
  4. Removing the Fuel Pump Sender (5:20 in the video)
    • Remove any debris with a broom
    • Remove the module retaining ring with a flat blade screwdriver and hammer
    • Pull the harness free from the hose to slide the ring off
    • Use a flat blade screwdriver to pry up around the outside of the fuel pump
    • Let it drain and remove the rest of the way
    • Drain out some of the gas
    • Use a container and funnel to recover any unused fuel in the tank
  5. Preparing the Fuel Pump Sender (6:40 in the video)
    • Remove the hoses by prying out the clips and swap them over
    • Push the fuel pump unit into place
    • Twist the cap
    • Insert the gasket
    • Place penetrating oil on the outside of the gasket
    • Push the fuel pump sending unit into place, making sure the arrow is facing the same direction
    • Slide the module retaining ring over the harnesses
    • Apply pressure to the sending unit, twist the ring into place with a hammer and flat blade
    • Re-clip the harnesses on the fuel tank bracket
    • File the gas tank strap pins if rusty
  6. Reattaching the Fuel Tank (8:55 in the video)
    • Reattach the passenger's side gas tank strap (the longer one)
    • Place the pin in the strap
    • Push the gas tank back up
    • Put the jack underneath the gas tank to hold its place
    • Replace the gas tank strap with the 13mm bolt
    • Reattach the driver's side gas tank strap
    • Reconnect the harness onto the fuel filter
  7. Reattaching the Fuel Line (10:05 in the video)
    • Reconnect the fuel pump electrical connector
    • Reconnect the hoses onto the fuel filter and replace the clips
    • Reconnect each of the hoses
    • Tighten the fuel tank filler tube hose clamps, let them slide back, and re-attach the yellow clip
    • Replace and tighten the hose clamps
    • Remove the jack
  8. Restarting the Car ( in the video)
    • Replace the fuel pump relay
    • Close the fuse box cover
    • Restart the engine, let it stall out, restart a second time

Tools needed for replacement:

    Pliers, Cutters & misc Wrenches

  • Bent Nose Pliers

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket

  • Specialty Tools

  • Drain Pan
  • Hammer
  • Jack Stands
  • Vise-Grips

How-to Video:

(10:53 min)

Tools List:

    Pliers, Cutters & misc Wrenches

  • Bent Nose Pliers

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket

  • Specialty Tools

  • Drain Pan
  • Hammer
  • Jack Stands
  • Vise-Grips



This part replaces:

  • Motorcraft PFS196
  • OE # 1F1Z9H307GB

Vehicle Fit

  • 2001 Ford Taurus Electric Fuel Pump and Sending Unit Module for V6 3.0L (excluding Flex Fuel) (Motorcraft)
  • 2001 Mercury Sable Electric Fuel Pump and Sending Unit Module for V6 3.0L (excluding Flex Fuel) (Motorcraft)
$336.95
Only 2 left in stock
Part #: MCFPU00006

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates
MOTORCRAFT
Brand #: PFS196

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est