Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Okay friends, one of the first things we need to do to start this job is to remove our negative battery terminal from the battery. Use your 8-millimeter, loosen it up, and get this away. Let's get inside the vehicle. Once you're inside the vehicle, go ahead and pull on this, raise your steering wheel, and then we're going to get right under here with a 5.5-millimeter socket, remove the mounting bolts. There it is. We'll set this aside so we don't lose it and we can move along. So let's make it till we can move this again. Take your small pocket screwdriver, carefully come right in between this area right here and we're going to try to separate these two pieces. The same on the other side, let's pull this down and out of here. Continuing with our 5.5-millimeter, remove this bolt, set that aside. There's one on the other side in the same exact location, you should be able to lift up on this a little bit. I'm going to try to get it out and around the steering wheel here. Take this off of here. There we are. It gives us a little bit more room.
Slide this up and out of here. So following our multifunction switch, we're going to be able to see on the backside of it, you have this wire right here, a little bit hard to see, this comes out of it, okay? I'm going to put the steering wheel in the upward position, lock this, and then if you follow it, it leads to this connector right here. So we're going to disconnect this and then of course, we'll draw it up. There we are. Get this out of those two wires. There it is. So now on the backside of the multifunction switch, you can see that there's a couple more wires. The top one has a push button on the inside area closest to the steering column, go ahead and push on that and then you should be able to draw this out. The lower one has the push button closest to you on the outside there, just go ahead and push on that and then draw that away as well. Now, right up along the top, you're going to see another mounting bolt. Remove that bolt and this should come right out. With that bolt out of the way, just push on this little tab right here and this slides right up. Get this in here.
If you notice you've got a little sliding area here and then of course, you've got the area on the back right there that you're going to slide that into. So just line those up, just like that, and then it should want to slide right in. Listen for a click to make sure it's locked in, and then install your mounting screw. Make sure it's nice and snug. Perfect. Let's grab our wiring, get that reconnected back there. That's one. Give it a nice tug, the second one, nice tug. We've got this one right here. Well, remember that this goes down and through there. Lift this up, and then connect it in right down here. Listen for the click, give it a nice tug, that feels good. Let's reconnect our battery. Make sure it's very tight and there's no movement to your terminal. So next you need to put your key in the on position and we're going to test our multifunction switch. We want to make sure it works before we go any further. Left directional, I can see it's functioning, right? Perfect. Wiper blades, awesome, and of course the squirter. You can't ask for much better than that. Let's turn off the key and continue. Let's get this back together. To start, we're going to go ahead and put the multifunction switch right through here, bring it all the way up, and now we need to put this lip underneath the steering wheel area.
Slide it in under there, around the outside here. Okay. This is looking pretty good. Slide this down, that looks like it's getting ready to line up. This side over here looks decent as well. Now we'll get this on there, it should just clip in. There we are. Let's put in our two mounting bolts that hold this together. We'll get that lined up as well. Start with the innermost portion here. Just slide it in. It's going to go behind the steering wheel. There we are. Okay. So that's one of the hardest parts, is just making it so the plastic clamshell goes in and behind the steering wheel. It's going to take a little finagling. Now let's get this rubber reattached. If you were to look at it, you're going to see that it has multiple layers, it has an inner level and then an outer portion. The inner portion goes behind the plastic and then of course the outer portion goes on the outside. Let's get that semi-lined up. I'm going to take the two pieces of my clamshell, just try to line them up together, and then squeeze them together. They should want to latch in to one another. There we are. Let's do the same to the other side with our mounting screw in along the bottom here. There we are.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the turn signal and wiper lever on this 2005 Ford F150. It's the same procedure for 2004 to 2005, also similar for '06 to '08, although a couple of the connections are a little bit different. The items you'll need for this is a new turn signal switch from 1AAuto.com, 8mm socket and ratchet, 7/32" socket, pick, flat blade screwdriver, 8mm wrench, two-jaw puller, and a T50 Torx bit.
Loosen up your battery cables with an 8mm socket and ratchet and just pull them free. If it's hard to get it off use a flat blade screwdriver to just separate the clamp a little bit and it should pull free.
Down here, underneath your glove box, pull out on this panel. Then using a flat blade screwdriver, pry down on the tab and pull that panel off. Then use your fuse puller and you may need to pry it out. Then on this row of fuses right here, with the red and the blue, you want to pull out this red 10. It's the third one in on this row just under that relay. That's to disarm your airbag.
Now, just pry out on this little panel here. There's a bolt inside of here that is 8mm. Just go ahead and remove that. Once you've removed that bolt and the one in the same spot on the other side, you can just pull this forward. Pry out on the red safety tab and then reach in behind and push down on the holding tab and pull the harness out. Now using a pick, just pry out the gray clip on this harness. Then pry out on the tab at the top and pull the harness free. Now, carefully set this aside.
Now just remove this 7/32" bolt underneath your steering wheel Push the tab on this harness and disconnect it, and then turn your steering wheel until it clicks. Then remove this T50 bolt. You can see here we have a two-jaw puller clipped in behind on the steering wheel. We're tightening it up pushing against the stud to loosen the steering wheel.
Now, pull down on this lever and then pull down on this panel. You want to push in at the same time, and it'll unclip. Then you just lift it up and out. Then, remove these two 7/32" bolts. We'll fast forward as Mike does that. Now lift this panel up and then pull it off the lever. Now remove this 7/32" bolt right here. Now push this tab and slide the switch up and off, and then push the tab to disconnect this harness and do the same for this one. To remove that last harness, we first have to pry up on this tab and unclip the other end of this harness. Now you can access that last harness, so you just push the tab and disconnect it.
On the left, is the old turn signal switch; on the right, is the new one from 1A Auto. You can see they're identical and they'll fit exactly the same. Using a pick, just pull out the spring of your old switch and then just drop it into your new one. Then, making sure the spring stays in, just slide that switch down into those slots until it's all the way down, and then reconnect those harnesses. Now, replace this 7/32" screw and tighten it up. Now, lift this up and put this panel back down over the turn signal switch, and then line it up. You want to slide it down onto that gasket and then replace those two 7/32" screws. Now take the lower panel, tuck it down in, and then you want to slide it up that gasket. Then clip the clips along the top back into each other and do the same thing on the other side, and then replace that 7/32" screw.
Installing the steering wheel there is a yellow dot on the shaft that should point to the top of your steering wheel. Reconnect this harness and replace this T50 screw.
Make sure your steering wheel is straight and then take your airbag and horn assembly, reconnect this lower harness, and then push that gray clip back in. Then, take this harness and push it back into place and push that red clip in to lock it. Once you get the airbag lined up you can replace the 8mm bolt on either side. We'll fast forward as Mike does that. Once you've replaced the bolts, make sure you've replaced those two covers as well. Now push your fuse back into place, put the fuse panel back on making sure your fuse puller is back in there. Then just put these tabs into those slots and close the panel.
Reconnect your battery cables and tighten up those 8mm bolts. Then just put this cover back down and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
