Replaces
Frequently bought together
Part Details
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an exterior door handle on this 2011 Chevy Silverado 1500. It's a similar process on a large variety of GM SUVs and pickup trucks from 2007 to 2012. The tools that you'll need for this is a flat blade screwdriver, a 10mm socket and ratchet with an extension, and a pair of needle nose pliers.
Using a flat blade screwdriver, you want to remove these three panels. The one behind the door handle, this door pull handle panel, and that triangular panel at the top there. Once those are removed, you'll see there are three 10mm bolts here. We'll fast-forward as he removes those. You want to remove this little panel under this handle right here. Pry that out with your flat blade.
Now you want to remove these two 10mm bolts right here. You want to pry up that switch panel and disconnect these harnesses. Just push in the tab on the top and pull back on them. For this lead there's a tab on the back of it. You want to pry out that tab and then the clip will actually pull up and out. Now pull your lock up and there's a little panel right here, just a little clip. You want to pry that out with the flat blade screwdriver. Once you pry that out you can lift that right up and off.
Now you can start prying off the door panel. Reach behind it and give it a sharp pull to release those clips. You want to do this all the way around the panel. Once you do that you can lift it off and then you want to tilt it. Now if you go in behind the door panel here, you'll see this door handle cable door here. Using needle nose pliers, push the clip inward and you can pull that up and out. Carefully remove your water shield. We did speed the video up. You want to remove it nice and slow. Do your best not to rip or tear it.
Now you want to remove this 10mm bolt right here, and you want to release this yellow clip. And then up, further up in the door, there's this little red tab here. You want to push the rod away from it towards the outside of the door. To open that clip, you literally just pop it open. This one, like I said, push it straight back. We'll fast-forward as he removes that bolt. Now remove this cap and that 10mm bolt in there. Pull the handle out. and then push it forward a little bit. and then it's kind of a little bit moving it back and forth, up and down a little bit to get it to release out from the door.
As you can see, there's nothing wrong with our old door handle, so we're just going to show you how to do this. You would remove that rod and then install it in your new door handle, and then remove this clip. This clip holds the lock cylinder in. Use a flat blade screwdriver and pry it out. You could also use a pair of pliers. Pull it out, and then there are two ways to put it back together. You see the lock cylinder comes out. Put the lock cylinder into your new handle.
You could either do it this way, then put the clip in, or you could actually put the clip in first and then snap the lock into the door handle with the clip in it already. To reinstall the door handle, you want to put that rod back down through the door. Slide it back and push it into place. We'll fast-forward as he replaces and tightens up those 10mm bolts. You want to re-clip those rods back into place and replace that rubber cap.
You can put your water shield back. Make sure that the wire harnesses and the door cable are pulled through. You want to make sure that these door panel clips line up in those holes, and that these hooks line up in these slots. Now you want to take that door handle cable, put it back into its clip. Pull back on it and feed it into that little spot there and run all your harnesses up through where the door switch panel is.
You want to make sure that this lock tab goes up through the door panel. You want to align the door panel up on the window sill. Then once it's lined up, you can push in the clips all the way around. Take your lock, slide it back onto the tab there, and reapply that little square clip. We'll fast-forward as he replaces the two 10mm bolts under this handle here, as well as the 10mm bolt behind the door handle. Now reconnect the harnesses to the door switch panel and push it down into place. We'll continue to fast-forward as he replaces that pull handle and the two 10mm bolts to secure it. Now you want to replace those four trim panels.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.
I'm just going to hit the dome lamp override switch to shut off dome lights, just so we don't run the battery down. Open up your door, and using small flat blade screwdriver or a small trim tool, remove a couple panels: one in behind your door handle—just twist lightly and pull that out; there's one right back in here, right in the middle—pull out and off; then the door lock knob, pull up on it lightly, and try and pry this center clip out at same time. Comes up and off. If you have good fingernails sometimes you can just pull up and off on that. You could also use a trim tool available on 1aauto.com. Put it underneath, pull straight up, make sure you pull up on the front. Somebody was not that careful on this one, and you can see they actually broke off the tab from the trim. Then you'll want to disconnect your power window switch, just a little tab here. Pull and disconnect. Then we'll remove three 10 millimeter bolts: one here and then two down underneath where your door pull is. 10 millimeter bolts, remove them with a 10 millimeter socket ratchet and extension. A lot of times these ones won't come all the way out, and that's okay. You can retrieve them when you get the door panel all the way off.
You'll want to use a trim tool. Once you get in there, you can see in behind there and see where the clips are. Got one here, roughly here and here. Pull out firmly, and work your way around. Then my bolts have popped out here, so I'll make sure I collect those. Once I'm sure I'm all the way around, lift up, and out. Then on here there's a couple of little tabs. I'm going to push the tab, pull out a little bit, twist it around, push the other tab. Push that through and out, and my door panel comes out. You can see there's actually clips on the padding here. It's still clipped on in a couple of spots. Just push those off.
Okay, we're going to remove the outer rear door handle on the Suburban. You could probably do it by just folding this vapor barrier down and getting in here, but we're going to pull it back so that we can make sure you can see it. To pull this vapor barrier off, it's got some butyl tape on here. Sometimes it'll peel off real easily. If it doesn't, I've got a razor blade here to help just cut it off a little bit. There you go. Put this aside so it doesn't get destroyed. Going to remove this rubber grommet with a plastic prying tool. Take our 10 millimeter socket. We remove this bolt that is holding on the door handle. I've got it loose. I'm going to try to take it out without dropping it inside the door panel. There we go.
Now we're going to remove the other bolt that is holding on the door handle. Inch in through here. All right, we've got this one loose. Oh, that one fell in. It landed on the door bar here. Before you take the door handle off, you've got to remove or unhook the clip that's on the actuator here. It's this yellow-ish, orange looking clip. Cut a little tab. Take a small, flat bladed screwdriver. Push open. It'll pop off. Now we can go to the outside of the door to remove the door handle. With the bolts and the door lock actuator rod removed, you're going to slide this handle forward. Then we're going to work it out of the door panel. It's going to come with the rod. That's how you remove the handle.
We're just going to clean this up a little bit before we install the handle back. Okay, so you take your actuator rod, you're going to feed it into the door opening. Do a little bit of maneuvering. Might have to open the handle because it'll move. Because it'll move this piece, it'll help you install it. There's some locating pins you're going to find. That's installed from the front. Now we need to put the bolts in and reconnect the actuator rod.
You need to reconnect the actuator rod because it's a little yellow clip. Kind of get it straight up and down. Press the rod in there, and then if you just sort of roll it up and over, it'll clip in. Kind of put a little bit of blue tape on this bolt to help hold it to the socket so I don't drop it. Go through this hole here. Sort of very gently thread this in. This is just a metal insert going into the plastic door handle. You don't want to over tighten these. You can break the door handle. Just as you feel them get tight. Install the second bolt. Just as it gets tight, stop because you don't want to break it. Reinstall the grommet. Now that we're all set working inside the door, we can reinstall the water vapor barrier. Just going to feed the wires through. Sort of find the general area as where it was. The butyl tape on there was still pretty sticky, so just kind of push it back down.
You have these longer, larger basically kind of teeth that hook into the square holes down there. Preliminary line everything up. Just make sure your harness goes up and through, and then reconnect your door handle cable in. and pull it out, push it in.
Again, just make sure that that harness is up through. You want this groove to go into the channel here, so lift up. Lift up, push down, and make sure your door lock is up through, your harness is up through, and then you should be able to see it nice and close to the door. There's a large line of pin up here. Once everything is good it'll go in about that far away, and then you can just set all the pins. You just need a pair of pliers, reach in, bring your lock back up. Put your three 10 millimeter bolts back in. One here, and then these two, and load into your socket. If you put some tape or painters tape on it might help hold them in place. I'll just put those in place. Reconnect the switch, feed the harness down in, and make sure you put this in correctly. Then your three pieces of trim, the one in behind the door handle, snap it in place. This one can just go down in place. This one make sure that the little tab is out. Put it down on, lock into place. That's all set.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks!
In this video, we're going to show you how to replace the rear outside door handles on this 2007 Denali. It's the same process for any 2007 to 2013 Yukon Denali, as well as the SLT, and Tahoe LTZ. It's also probably the same procedure or a similar procedure for rear doors on the Yukon XL, Suburban, as well as the four-door Sierra and Silverados with the LTZ Denali or SLT trims.
Items you'll need include handles from 1AAuto.com, small and regular flat blade screwdrivers, 10mm socket with ratchet and extension, and a door panel clip tool or putty knife.
Disconnect the battery. You want to open up the driver's door, pull the hood release lever, hit the safety hatch, move it to the right, and then lift the hood up, and the battery is near the rear of the engine compartment on the passenger side. There's a 10mm nut on top of the negative battery cable. Loosen that 10mm nut and pull the battery cable up and off, and then put it to the side so it won't contact the terminal again.
Open up either rear door. The procedure is the same for both. You need a small flat blade screwdriver, and you'll pry out that square clip, pry out this panel under here, and I am just using one hand, so it does drop to the ground, one hand holding the camera, one hand working the screwdriver. Then there is also a little panel underneath here that you pry out. Once you have that panel out, it'll expose a 10mm bolt there, and then there's another 10mm bolt to remove down here.
Use a small screwdriver and pull up on the walk knob and pry that clip out, and it comes up and off. I'll fast-forward here as I remove those two 10mm bolts. Use a plastic trim tool or a rag and a flat blade screwdriver, and pry up on the switch panel. You kind of pry up in the center and then you pull it up and it locks. The clips are on the front and the rear. Once you get the center up, you just kind of work it into the front, and then work it into the rear. It comes up and off and then the harness just has a tab on it. You press the tab and unplug it.
Use a rag to protect your paint and a door panel clip tool, or you could use a putty knife, but you work either the tool or the knife in underneath the clip. You'll basically feel that you slide it through and you can feel the plastic clips, and then you pull out and release the clips, and I usually do this for two or three of the clips on the back side. Then you can work your hand underneath and release the rest of the clips.
Once the clips are released, you pull the panel up and off of the window ledge clip. If your door panel has never been off before, the water shield, the white water shield you can see is a black clip holding it to the door panel. There's probably three or four of these little black clips. You can see how you try to use the clip tool or a screwdriver to pry the clip out. Eventually, I just end up grabbing ahold of the clip and the water shield at the same time and pull them out. Again, you'll have to do this probably three or four times if your door panel has never been off before.
We'll need to undo the door handle cable clip. There's two little clips that hold the cable in. I'm just prying with a small screwdriver to release those clips. Here's a better shot of them as they come out. You pull it out and up out of the handle, and then the door panel comes right off. I do find one more of the clips that clip the water shield to the door panel and release it. Carefully pull the water shield back and release the adhesive and expose the inside of the back part of the door. You want to unclip the door lock rod, see the yellow clip right there, reach up with your hand, try and get a good shot here, and you just pull on the outside edge of that clip and release it and pull the rod out.
You want to remove this round rubber grommet. You push from the back side and pull it off, and then there is a bolt up in there as well as another bolt that holds the door panel. 10mm socket, ratchet, and extension, and go right in through and undo those two bolts. Now the handles slide forward and out. You'll want to remove the latch rod from the old handle. Just kind of twist it and pull it up and out. Then install it in to your new handle. Install the new handle, just pull on the protector plastic back, put the rod down in, and then might need to pull the handle out a little bit as far as just the handle part out, but you can slide it up in there, and then you push it on to the door and slide it back to lock it in place.
Reach up and start the bolts in to the back of the handle. You can see it's easy enough to get your hands up in there, and you can even get them up into the back side, too. Start the bolt in and then tighten them up. Tighten them up nice and firm, don't overtighten them. You don't want to strip the thread. Reach in, put that latch rod back in place, and then lock the clip in place. Be sure your door is unlocked. You can test it out.
Install that rubber grommet and press the shield back up in place. To reinstall the door panel, get it close, put the ball of the cable into the door handle, then pull the cable around and clip it in. Move the panel close to the door, make sure that the harness comes up through, and then make sure that the door lock goes up through the hole there, and then you kind of lift the panel up and push the top on and set it down into that window ledge clip, and then you can kind of look in behind, make sure that the clips line up. Once you have everything lined up, then you can reset the clips.
Make sure that you pull the lock knob up and then put the lock trim on there. Set that, make sure you leave it unlocked, and then reinstall the two 10mm bolts that hold the panel in place. I'll fast forward as I do that. When you tighten these, tighten them up firm, you don't want to tighten them, though, and make sure you have the harness pulled up through, put the two trim pieces in place. The upper one, you want to put the rear end first and then snap the front end. It snaps in at the front first on me, so I have to pull it back out, and then put it in correctly. Again, the back towards the back goes in first, and then front snaps in, and then reconnect the harness and snap the switch panel down in place, and then do a little test.
Then reconnect your battery, and then you should be all good to go. Put the negative battery cable back on the post and 10mm socket, ratchet, and extension, then tighten it up.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
Tools used
Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years.
What's up, guys? I'm Andy from 1A Auto. Today, I'm going to show you how to remove and reinstall an outside door handle on this 2008 Chevy Silverado work truck. If you need parts for your vehicle, click the link in the description and head over to 1AAuto.com.
Open the door. We're going to remove this window crank. We need a window crank removal tool, so we're going to position the window crank in this position right here. Take the tool. If you want to put it in the same location that it was, you could mark it before you take this off. Then we can get this, just slide this down. There's a little pin, little clip we have to remove. Just push it down and then it slides right off.
To take this lock button off, I'm just going to use a pick tool. Just get in behind here and slide that little walk piece off. Slide the button off. Next underneath here, I'm gonna take a trim tool. Just slide under here. You can use a pick also. Get underneath there. Slide this cover off. Next, we're going to take this cover off. Take my pick tool or trim tool, slide that cover off. There's a clip right there, a clip right there. We're going to use a 10mm socket, extension, and a ratchet, and there's three bolts. One bolt here and two bolts there. Take those out. Might have to hold this handle up a little bit to get this bolt out. Take that bolt out. Oops. We'll just use a magnet to take that bolt out.
Next we're going to take this trim piece off, just use my trim tool. Get it behind here and pry. It's just clips that hold us on. Three clips hold that on. Next, I'm going to use a trim tool. I'm going to pop those clips holding the door panel on. Just go around the perimeter of the door panel and pop it off. Once those are all popped off, it should be able to release right there.
We're going to need to release the handle cable right here. There is two ears on the bottom of this door panel so you can put it in service position so that you can leave it there while you're working. All right. To take this cable off the inner door handle, I'm just going to use some needle nose pliers. Get in there, just get a squeeze. There's a tab, a couple tabs. I'm going to squeeze on the cable. That will release. Sometimes if you twist it a little bit it helps out. Pull the cable, slide it off, and then there's a ball on the end of the cable. This is where the two tabs are. You just need to squeeze these two tabs, just like that, to release it. Now I can grab the door panel and just slide it out. If you rolled your window down, we're going to roll it up at this point. I'll just take the handle off.
Next, we're to take this inner vapor barrier off, or installation off. I'm just going to slide this. Some sticky adhesive is attaching it to the door. Generally, it peels right off fairly easily. Just being careful not to rip this. If it does rip, you can use some tape to tape it back together. Just fold it down out of the way. I'm going to take these two plugs off first, we'll just use a trim tool. Pull those off.
All right. We want to disconnect these rods that go from the door handle to the door latch. There's a little yellow retainer right here that holds it on. Need to grab with your fingers on the back side. We're going to slide it out, pop it off just like that, and that rod will come off. Then for the top rod that goes to the lock cylinder, I'm just going to take the rod and I'm going to push it towards the outside of the door. Sometimes this is a little bit tricky. I'm going to try using a pick tool to get in here and twist it.
There's two 10mm bolts that I'm going to take out. One through this whole, just use a 10mm socket, extension, and a ratchet. Take that one out. Then also through this bottom hole over here. Slide that one out. Now I can go from the outside. Just grab the handle, just slide it towards the vehicle a little bit. Just pry this out a little. You can slide the handle right out.
To take this lock cylinder off, I'm just going to take a straight blade screwdriver, just a little clip retainer holding on right here. Just pry that that way a little bit and I can push straight through just like that. Slide the lock cylinder out. Reinstall the lock cylinder, just push the lock spring back in. Take it, just push it, lock it back in place. Make sure the lock cylinder is all the way down.
So on this handle, this piece actually broke. This is the rod that goes into there, so this piece would need to be replaced. We're going to slide this back into position, slide that rod down here. I'm just going to open the handle a little bit. Slide that in just like that. Once that's in, I'm going to pull it back towards the vehicle a little bit and it'll slide in towards the outside of the vehicle. Okay. Now we'll take the 10mm bolt and slide this into position here. Right there. Snug that up. We're going to take the other 10mm bolt. It's going to go through this hole, in right there. We'll snug that up. Now I'm going to put these caps over the holes. Just push them back in just like that.
Then on the inside, this rod is going to go to the door lock cylinder. You're going to get it lined up. There's like a V and it's going to go in the middle of the V. You grab it and just pull. Lock it into place. We're going to push this into this retainer. It's like a door, you open the door. This is going to get lined up right there. Once that rod is in there, then close the door. Make sure that's latched. You can grab the handle and just make sure that operates properly.
Now, slide this into position. Pull the cable through here like that. There's a hole right here that the door has a pin that goes through there, so get that lined up. That looks pretty good. A lot of times on these door panels, this little bracket breaks off the door panel. Right here. It's a common problem. It's not something that's extremely crucial for putting the door panel back on, the door panel will stay in position even with that broken, so don't worry about that too much. We can take the door panel and make sure this lock rod goes through that hole right there. That's good right there. Get this little door pin in the hole on this side. That's in position. Make sure the rest is there. Once all the pins are lined up, you can start pushing it on.
I'll reattach this. If you had a foam insulator, you would put that in there now. This vehicle doesn't have one, Line these pins up, lock that in place. We're going to take these two bolts right underneath the handle. Use our 10mm socket, extension, and ratchet. Just get that one started and then I'll get the other one started. Snug it up then I'll snug up the other one. Down below here underneath the handle, get this bolt in. We're going to tighten it down. Snug it down.
Take these two covers. This one's going to go down below. There's a little pin right there that goes through that hole so you know which direction it goes. Get that in position. Lock it in place. This one is going to go in this position. There's a pin little slot there. Lock that in place.
All right. Now I'm going to install the new crank handle. Remember this washer? It's going to go on the back side. Just put this into position. Put it on the same way that you took off the old handle. Get it lined up. Make sure it's locked in place and it's good to go.
Then we'll take this lock button. Make sure this lock rod is all the way up. Take the button, slide it into position, and then push down on the lock part. Make sure it works properly and you're all set.
Thanks for watching. Visit us 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
