Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a rear window regulator on this 2003 GMC Envoy XL. It's the same part and similar process on the regular Envoys from 2002 to 2009. The items you'll need are a new rear window regulator from 1AAuto.com, flat blade screw driver, a 7mm and 10mm socket and ratchet, and a putty knife.
Start off by prying up this little cover with a flat blade screw driver. Then remove those two 7mm bolts. Stick a putty knife behind the door panel and slide it down until you find the first clip and pry out and reach in behind the door panel and just pull out around each clip. Once you remove each of those clips, you can pull the door handle back. Then just push this switch from underneath. It comes up and out. Then push the tab on the harness and disconnect it. You could technically do this before removing the door panel, but you're more likely to scratch up your door panel if you do that. Remove your water shield. Having a razor blade can help because you can just cut at the adhesive, but you can also just pull it free.
This is a cable activated regulator, and a lot of times when they break, what you'll be able to do, you'll hear a popping and grinding noise, and then your window will actually move up and down. So, once you get the door panel off, you'll want to move it to this position where you can get at this 10mm nut and this 10mm nut, and you're going to loosen those. Before we do that, we'll just take a screw driver and push on this tab here and push the connection out. Pull the window up and out of those clamps. Then push the tabs on this clip and push it through the door. Then remove these two 10mm bolts and loosen this top one. Tilt your window regulator and then lift it up and unhook it and pull it down and out of the door.
On the left is the old regulator. On the right is the new one from 1A Auto. You can see they're identical, and they'll fit exactly the same. Remove that top bolt from your old regulator and thread it into your new one just loosely so that you can hang it up in the door. Take your new window regulator, feed it up into the door, push that bolt through the top and hang the regulator and then just line it up and replace those other two bolts. We'll fast forward as Mike does this and tightens them both up. Push this clip back into the door, loosen up these window clamps, reconnect this harness, and then slide the window down into those clamps. Once you have it all the way in and clamped down, tighten up those two 10mm nuts, put your vehicle into accessory, plug in the switch, and just test out the regulator. You can see it works. You can just disconnect the switch and make sure you put your car back in the off position.
We'll fast forward as Mike replaces that water shield. To replace your door panel take the small panel and push it back onto these studs. Then, push the harness for that switch back up through the hole in the door panel. Line up the clips on the door panel, and once you have them all lined up, just hit them into place. Reconnect the switch and push it down into place, and then replace those two 7mm bolts and tighten them back up. Now just replace the small cover, and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
