Chevrolet GMC Cadillac Passenger Side Mirror Trail Ridge TR00104

Take this panel off. Just gonna use a trim tool. Just get behind here, pry it out, and then up this little clip right there, those two little pins. Take this cover off next. Just get under here. And there's some clips. There should be a clip right there, looks like it broke before. And then this slides out. Take this little cover off. You could use either this trim tool or even a small screwdriver. Now, take the trim tool, get under here and just push it out a little bit. Pry it and then it's gonna slide towards the back. There's a pin right there, two little clips right there. And just use a trim tool. Get under here and just pry this out. It's just a push pin, just like that. Now we're gonna take these two bolts out. Just move this lock rod to the back. There's a bolt right here and a bolt right here. Use a 7-millimeter socket. Take that bolt out and this one. The lower one is the longer one. Take this bolt out. Use a T20 socket.

Now, just grab the door panel. You want to slide up and then come out slightly. You don't wanna break any of those clips. And it's gonna be hard to see, but you have to reach to grab the wires. Disconnect the wires for the window switch. And over here, push down, this is like a ratchet retainer. While this is in there there's a little button right there you push and then you ratchet this down and it disconnects that. And one more connector. And these all have push pins or push retainers, push locks. Just push all those down. Over here just pull this light socket out. Just pull it towards the vehicle. And carefully, there's a bulb right there. And pull the door panel off. And take this wire out. You might have to pull the vapor barrier back a little bit. There's some retainers right here and right here. Just use a trim tool. Pop these wires off. Sometimes they break like that. That's okay. And take these nuts off. Use a 10-millimeter socket. When I go to take the last one off, just make sure you support the mirror from falling. It should stay in. Should be retained by those, but just for safety. All right. Grab the mirror from the outside and slide it through. Put the wire through and there we go.

So, the new mirror generally comes black just like that. You could leave it like that if you wanted to or you could swap this piece over from the old one or you could even paint it to match the vehicle. To take this off, what I'm gonna do is take the glass off first. Take a straight blade screwdriver, get behind here. These are clipped in, could always use a pick to try to unhook these. And then this front cover is snapped in, so just take the trim tool. Just pry in here. When you do that, try to unlatch it right there. That one broke a little bit. And just slide it over. For this one, use the screwdriver, pop that off, and just slide over a little more. There is some adhesive tape on here. Same on here. Slide that off. When taking this off, these old tabs are gonna break most likely. You can be careful and try to do it the way we did it. But for the most part, they break. What you can do is use double-sided tape, just clean up this area and re-adhere it to the new one.

With the new mirror, there's these little protectors. Take those off and take the wires, fish them through the hole and slide through. And take the nut, get the nut started. All right. And tighten these up. Snug those up. That's good. Gonna re-secure this wire with wire ties. All right. And re-secure the vapor barrier. Put this insulation back in. And connect the connectors.

That's good. Take this light, slide that back in position. That's good. All right. Line the door panel back up. And you actually have to move this lock rod towards the outside of the door. With that all lined up, then you can push it down. Just make sure it's in all the way around. Put these screws back in. Get that started. Tighten it up. And then put the screw that goes right there. This is the smaller one. Get that one started and I'll get this longer one started. And tighten these up. And push this push pin back there. This cover is gonna go over here. Pop that back on. Pop this cover on, slide it over the handle. Put the front in first, down, and push it in. This lock is gonna go...you have to move the locker out again. Move it to the unlock. Slide this front end first, lock it into place. Make sure it works. And this last piece of trim right here. Line it up, lock it in place.

I'm going to take this trim piece off, use a trim tool, just get behind here. I'm going to just pry it out, there's some clips, hold it on, and then it slides up. Right here, we're going to take this knob off, just take the trim tool on the backside and just slide it out. There's some clips right there, and it slides in right there. And down below here, take this trim off using the same trim tool. And slide it out. I'm going to use a 7-millimeter socket, take this screw out right here. And there's another screw right here under the handle. And then we're just going to grab the handle and the bottom part of the panel and lift up gently and slide it out.

There's a wire that goes right here to the light bulb. We're going to try to slide the light bulb socket out and disconnect the connectors over here. Just push down on the tab right there and push down on that tab. And then the last one, there's a ratchet mechanism, just push down on the center part to get to slide the ratchet over. Here we go. I'll show you how this works. When this is pushed down, what you need to do is push down on that little button and then slide this over, and it will push the connector out. Now we're gonna move this vapor barrier, just peel back on this a little bit, be careful not to rip it. And follow these wires down. Take this wire, and it looks like this one was taped on here. Normally, it won't be taped, there'll be a pushpin right there holding in it, like this one.

Take a trim tool, skip behind the pushpin and slide it up. Same with this one. And take this insulation off, set it aside. And there's three nuts holding this on. And take a 10-millimeter socket and take these nuts off. When you go to take the last one off, before you take it off completely, you want to support the mirror from the other side and slide the mirror out. And it might be stuck on or still holding on by these little tabs right here, push on those tabs and slide the wires through. And there it is. Now with the new mirror, it's going to come with this shield not on the mirror, so you can actually paint it to match the vehicle. You can attempt to remove the old one, all you need to do is take off the mirror. To get the mirror off, you just slide the mirror outwards, this vehicle doesn't have a mirror. And then take a screwdriver and just try to pry and it's clipped in right there. And then just take a trim tool, get underneath the trim slightly. Then you can just take a screwdriver, get in behind here. Try to push those tabs out. Just like that. And sometimes they crack, that's why it's sometimes better to just paint the new one.

And you're also gonna want to work all the way around and slide it out. There was a little bit of double-sided tape on there. And I only broke one of these up. That one broke too, so two of those. So in this case, I would need some double-sided tape to put this one back on. And install it. Just line these tabs up, those slots. And just give it a little pressure then clip it in. Right, take the mirror, slide the wire through. And line up with the studs. While you're holding the mirror, it's a good idea to have one nut in your hand and just get that started. Now take the other nuts and get those started. Just try to tighten them down evenly. Good. Now just take the insulation, put that back, then you can take the wires and push the retainers in. And if these retainers don't come with the new wires, you can just tape them up, cut them off the old wires. Or even if you want to, you could use wire ties and slide this through the vapor barrier. And reattach the vapor barrier. You can use some butyl tape if it doesn't stick very well. All right. Now we can connect these connectors. Just line this one up, and ratchet that down. Line those up, it's a little bit tricky. And then connect that tweeter speaker and take this light socket and just slide it in position and slide the door panel. These clips are going to slide in first with it a little bit. Once it's flush, you're gonna push it down and just check all the way around, make sure it's in properly. And take these two screws, take the smaller one, it goes up here. Snug that down and a larger one goes right in here. It's good. And take this cover, it's gonna slide in here first. Make sure it works. Take this lower cover, and this part's gonna slide in first after you go over the handle. And push it down, and this cover, this bottom part is gonna go in. And slide it in position. Lock it down.

Take this panel off. Just gonna use a trim tool. Just get behind here, pry it out, and then up this little clip right there, those two little pins. Take this cover off next. Just get under here. And there's some clips. There should be a clip right there, looks like it broke before. And then this slides out. Take this little cover off. You could use either this trim tool or even a small screwdriver. Now, take the trim tool, get under here and just push it out a little bit. Pry it and then it's gonna slide towards the back. There's a pin right there, two little clips right there. And just use a trim tool. Get under here and just pry this out. It's just a push pin, just like that. Now we're gonna take these two bolts out. Just move this lock rod to the back. There's a bolt right here and a bolt right here. Use a 7-millimeter socket. Take that bolt out and this one. The lower one is the longer one. Take this bolt out. Use a T20 socket.

Now, just grab the door panel. You want to slide up and then come out slightly. You don't wanna break any of those clips. And it's gonna be hard to see, but you have to reach to grab the wires. Disconnect the wires for the window switch. And over here, push down, this is like a ratchet retainer. While this is in there there's a little button right there you push and then you ratchet this down and it disconnects that. And one more connector. And these all have push pins or push retainers, push locks. Just push all those down. Over here just pull this light socket out. Just pull it towards the vehicle. And carefully, there's a bulb right there. And pull the door panel off. And take this wire out. You might have to pull the vapor barrier back a little bit. There's some retainers right here and right here. Just use a trim tool. Pop these wires off. Sometimes they break like that. That's okay. And take these nuts off. Use a 10-millimeter socket. When I go to take the last one off, just make sure you support the mirror from falling. It should stay in. Should be retained by those, but just for safety. All right. Grab the mirror from the outside and slide it through. Put the wire through and there we go.

So, the new mirror generally comes black just like that. You could leave it like that if you wanted to or you could swap this piece over from the old one or you could even paint it to match the vehicle. To take this off, what I'm gonna do is take the glass off first. Take a straight blade screwdriver, get behind here. These are clipped in, could always use a pick to try to unhook these. And then this front cover is snapped in, so just take the trim tool. Just pry in here. When you do that, try to unlatch it right there. That one broke a little bit. And just slide it over. For this one, use the screwdriver, pop that off, and just slide over a little more. There is some adhesive tape on here. Same on here. Slide that off. When taking this off, these old tabs are gonna break most likely. You can be careful and try to do it the way we did it. But for the most part, they break. What you can do is use double-sided tape, just clean up this area and re-adhere it to the new one.

With the new mirror, there's these little protectors. Take those off and take the wires, fish them through the hole and slide through. And take the nut, get the nut started. All right. And tighten these up. Snug those up. That's good. Gonna re-secure this wire with wire ties. All right. And re-secure the vapor barrier. Put this insulation back in. And connect the connectors.

That's good. Take this light, slide that back in position. That's good. All right. Line the door panel back up. And you actually have to move this lock rod towards the outside of the door. With that all lined up, then you can push it down. Just make sure it's in all the way around. Put these screws back in. Get that started. Tighten it up. And then put the screw that goes right there. This is the smaller one. Get that one started and I'll get this longer one started. And tighten these up. And push this push pin back there. This cover is gonna go over here. Pop that back on. Pop this cover on, slide it over the handle. Put the front in first, down, and push it in. This lock is gonna go...you have to move the locker out again. Move it to the unlock. Slide this front end first, lock it into place. Make sure it works. And this last piece of trim right here. Line it up, lock it in place.

I'm going to take this trim piece off, use a trim tool, just get behind here. I'm going to just pry it out, there's some clips, hold it on, and then it slides up. Right here, we're going to take this knob off, just take the trim tool on the backside and just slide it out. There's some clips right there, and it slides in right there. And down below here, take this trim off using the same trim tool. And slide it out. I'm going to use a 7-millimeter socket, take this screw out right here. And there's another screw right here under the handle. And then we're just going to grab the handle and the bottom part of the panel and lift up gently and slide it out.

There's a wire that goes right here to the light bulb. We're going to try to slide the light bulb socket out and disconnect the connectors over here. Just push down on the tab right there and push down on that tab. And then the last one, there's a ratchet mechanism, just push down on the center part to get to slide the ratchet over. Here we go. I'll show you how this works. When this is pushed down, what you need to do is push down on that little button and then slide this over, and it will push the connector out. Now we're gonna move this vapor barrier, just peel back on this a little bit, be careful not to rip it. And follow these wires down. Take this wire, and it looks like this one was taped on here. Normally, it won't be taped, there'll be a pushpin right there holding in it, like this one.

Take a trim tool, skip behind the pushpin and slide it up. Same with this one. And take this insulation off, set it aside. And there's three nuts holding this on. And take a 10-millimeter socket and take these nuts off. When you go to take the last one off, before you take it off completely, you want to support the mirror from the other side and slide the mirror out. And it might be stuck on or still holding on by these little tabs right here, push on those tabs and slide the wires through. And there it is. Now with the new mirror, it's going to come with this shield not on the mirror, so you can actually paint it to match the vehicle. You can attempt to remove the old one, all you need to do is take off the mirror. To get the mirror off, you just slide the mirror outwards, this vehicle doesn't have a mirror. And then take a screwdriver and just try to pry and it's clipped in right there. And then just take a trim tool, get underneath the trim slightly. Then you can just take a screwdriver, get in behind here. Try to push those tabs out. Just like that. And sometimes they crack, that's why it's sometimes better to just paint the new one.

And you're also gonna want to work all the way around and slide it out. There was a little bit of double-sided tape on there. And I only broke one of these up. That one broke too, so two of those. So in this case, I would need some double-sided tape to put this one back on. And install it. Just line these tabs up, those slots. And just give it a little pressure then clip it in. Right, take the mirror, slide the wire through. And line up with the studs. While you're holding the mirror, it's a good idea to have one nut in your hand and just get that started. Now take the other nuts and get those started. Just try to tighten them down evenly. Good. Now just take the insulation, put that back, then you can take the wires and push the retainers in. And if these retainers don't come with the new wires, you can just tape them up, cut them off the old wires. Or even if you want to, you could use wire ties and slide this through the vapor barrier. And reattach the vapor barrier. You can use some butyl tape if it doesn't stick very well. All right. Now we can connect these connectors. Just line this one up, and ratchet that down. Line those up, it's a little bit tricky. And then connect that tweeter speaker and take this light socket and just slide it in position and slide the door panel. These clips are going to slide in first with it a little bit. Once it's flush, you're gonna push it down and just check all the way around, make sure it's in properly. And take these two screws, take the smaller one, it goes up here. Snug that down and a larger one goes right in here. It's good. And take this cover, it's gonna slide in here first. Make sure it works. Take this lower cover, and this part's gonna slide in first after you go over the handle. And push it down, and this cover, this bottom part is gonna go in. And slide it in position. Lock it down.