Chevrolet GMC Cadillac Idler Arm Bracket Assembly MOOG K6723

You wanna keep in mind when you're doing this job, after you're done, you're gonna wanna go to a local garage and have the vehicle aligned so you don't have premature tire wear.

Just take this cover off. Use a 15-millimeter socket. There's two bolts on the bottom, two on top, sometimes there'll be a third. Slide it off. Take this cotter pin out. Just use some side cutters. And pull that out. Just gonna use a little rust penetrant, it's a little rusty. Take a 21-millimeter socket, take this nut off. Now I wanna separate the idler arm from the steering bar. I'm just gonna use a front-end [SP] tool. There's many different tools you could use to get this off. Just tighten this up. Put the nut on just so my tool doesn't slip off the stud. Just gonna use it as a guide. Another way you could try do this is use the pickle fork. There we go. Slide that out.

Gonna take these two bolts out. I'm gonna use a wrench, a 21-millimeter wrench backside to hold the nut. Use a 21-millimeter socket on the bolt. Take both of those out. Pull the bolts out. Just grab the whole idler arm assembly and just slide it out.

If you're gonna replace just the arm or just the assembly, you're gonna have to separate it. So use a 24-millimeter socket. It helps to put it in a vise. And then you can use a puller and separate these two. Just like that. And take the arm, put the new nut on. Just snug that up tight.

All right, just line this up. Gonna have to tap this in place. It's good.

Before you put the bolts through up top, just make sure it's going through this bar right here. We'll put the bolts in. Take the two nuts, get them on the backside. Now snug these up. Torque these bolts to 74-foot-pounds. And take the castle nut, install that there. Tighten it up. Then torque this to 46-foot-pounds. If the hole didn't line up you can just tighten it up a little bit more so you can put the cotter pin in. Slide the cotter pin in. And just bend one of the tabs over. And trim the excess. Take the shield, install it. Put the bolts back in. And tighten these up.

All right, friends. So, one of the first things we need to do is safely raise and support the vehicle. Once you've done that, you wanna come right upfront to this skid plate right here. Go ahead and remove all 15-millimeter bolts that hold it in. Now, that that's out of the way, let's come right over here to where the idler arm comes down through this arm right here, remove the 21-millimeter nut.

Now, the next thing we would need to do to get this arm out of here, is of course try to drop this sway bar out of the way. If your bolts look like ours do, and you think that they're gonna be an issue, I would just skip right past that and we'll come right up here and we'll remove the whole idler unit right here. To get this out of here, we're gonna use a 21-millimeter right there, and then we'll use a 21-millimeter wrench on the nut side.

Let's put a nice piece of wood in between the frame and this bar right here, just to make it so this bar can't go up too far while we hammer on this right there. Now that that's out of there, we can grab right onto this and we'll get it out of the vehicle. Now, when you're replacing your idler arm bracket assembly here, you're gonna have to remove it from the idler arm. To do that, you'd remove this nut right there, and then you'd do something as simple as a pickle fork coming in between here, or you could even use a puller to separate the two. Odds are, if your idler arm bracket assembly is no good, more than likely at the joint at the idler arm itself is no good as well. In which case I would just replace the both as a pair, that's much easier that way as you can tell. But for the purpose of this video, I'll still show you how to get them apart.

Now to remove this, I like to have it nice and level on the ground and I'll put my foot on it. I'm gonna have it so it's facing down towards the left, so when I remove this and it tries to spin, you can't go anywhere. I'm just gonna use this pickle fork right here, put it right in between the joint, and then give it a couple of loving bonks with my hammer. As you can tell, the two separated at this point, this joint is no good, but that's okay, we're replacing this anyway.

The next thing I like to do is put the unit right inside of a vise if you have access to one. You wanna grab onto this boot, take a look underneath there, make sure there's plenty of grease, go ahead and push it down, that feels great. Now we're gonna take that idler arm, set it right down on there. Take our brand new nut. You always wanna use a brand new nut, okay. So, now if I use my 24-millimeter wrench and I try to tighten this, what you're probably gonna notice is the stud on the inside is gonna start spinning once it gets to a certain point. Okay, so as you can see, it's spinning the stud. Is the nut all the way down? No it's not. So, now we're gonna use a hex bit and you wanna use an 8-millimeter. Come right inside there, that's gonna hold it and now we'll continue tightening this. Make sure it's nice and tight. That feels great.

It may be time to get our unit back up inside the vehicle here, spring it right up and in. Behind those lines, hopefully. Get that in the center link. Let's get this into its bracket. Okay, that looks decent, let's grab our two bolts. Make sure that they have washers, there right through. The other one, here we are. Let's grab the washers and the nuts for the other side. Now let's snug these up. Now let's go ahead and torque these down to 73 foot-pounds

Torqued. Let's get this nut on there. Snug it up, torque this to 46 foot-pounds. Torqued and use our locking cotter pin, slide it right on through there. And then make sure you pin it over, so there's no way this nut can come loose. Get this out of here. Awesome. Let's get this shield back up on here on, I'm gonna line up those holes. Start in all the bolts, before I tighten any of them down. Perfect. The next thing that I would wanna do, is make sure that I get it down to a reputable alignment shop.

You wanna keep in mind when you're doing this job, after you're done, you're gonna wanna go to a local garage and have the vehicle aligned so you don't have premature tire wear.

Just take this cover off. Use a 15-millimeter socket. There's two bolts on the bottom, two on top, sometimes there'll be a third. Slide it off. Take this cotter pin out. Just use some side cutters. And pull that out. Just gonna use a little rust penetrant, it's a little rusty. Take a 21-millimeter socket, take this nut off. Now I wanna separate the idler arm from the steering bar. I'm just gonna use a front-end [SP] tool. There's many different tools you could use to get this off. Just tighten this up. Put the nut on just so my tool doesn't slip off the stud. Just gonna use it as a guide. Another way you could try do this is use the pickle fork. There we go. Slide that out.

Gonna take these two bolts out. I'm gonna use a wrench, a 21-millimeter wrench backside to hold the nut. Use a 21-millimeter socket on the bolt. Take both of those out. Pull the bolts out. Just grab the whole idler arm assembly and just slide it out.

If you're gonna replace just the arm or just the assembly, you're gonna have to separate it. So use a 24-millimeter socket. It helps to put it in a vise. And then you can use a puller and separate these two. Just like that. And take the arm, put the new nut on. Just snug that up tight.

All right, just line this up. Gonna have to tap this in place. It's good.

Before you put the bolts through up top, just make sure it's going through this bar right here. We'll put the bolts in. Take the two nuts, get them on the backside. Now snug these up. Torque these bolts to 74-foot-pounds. And take the castle nut, install that there. Tighten it up. Then torque this to 46-foot-pounds. If the hole didn't line up you can just tighten it up a little bit more so you can put the cotter pin in. Slide the cotter pin in. And just bend one of the tabs over. And trim the excess. Take the shield, install it. Put the bolts back in. And tighten these up.

Normally, there is a shield right here, you wanna take that shield off. There'll be four or five 15-millimeter bolts. Take that off, get it out of your way. Now, we're gonna take this nut off. On this vehicle, there's a cotter pin. So, I'll just use some side cutters, take this cotter pin off. Just bend it back a little bit and just pry it out. And sometimes they break. There we go. Now, I'm gonna take a 22-millimeter socket, take this nut off. Now, I wanna remove that stud from the steering linkage that goes through the idler arm. I'm gonna use a tool like this, it's gonna press it out. You can use a couple other methods. You could use a pickle fork, try to get it out this way...that way. Just gonna put the nut on to stabilize the tool so it doesn't fall off. All right. While that's on there tight, I'm just gonna give it a tap with the air hammer, see if the vibrations loosen it up. So, that didn't work out. So, I'm gonna try a pickle fork. Sometimes these are tricky to get to separate. There we go.

Now, I'm gonna take these two bolts out. I'm gonna use a 21-millimeter wrench. On the backside, there's a nut and then a 21-millimeter socket on the front. Get that nut off. Take the bolt out. And just grab the idler arm and the housing and just slide it up. If you were gonna replace one of these pieces or the other, you can separate that nut. Just gonna put the housing in the vise, make it easier to install. Take the nut off. All right. Take the idler arm, put the nut on, take a 24-millimeter socket and snug it up. Now, I'm gonna take this castle nut off. And get this in position. As you slide the housing in the bracket, you wanna make sure the idler arm goes through the steering linkage. Get the bolts lined up. And put the nuts on the backside. Now, I'll tighten these down. Then torque both of those bolts to 73 foot-pounds. Now, install the castle nut and tighten that up. And then torque this to 46 foot-pounds. And find the hole through the stud and you can use the cotter pin, slide it through. If it doesn't fit or if you can't get it to line up, you can tighten the nut up a little more so it does line up. There we go. And use some side cutters and just bend this like this. And then you can trim the excess. Now, if you have that shield right here, reinstall that shield.