2000 Chevrolet Tahoe V8 5.7L 10 Piece Lighting Kit DIY Solutions LHT04066

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to service the headlight bulbs as well as replace the entire headlight assembly on this 1996 Chevy Tahoe. We show you on the passenger side, but the driver side is the same procedure. The items you'll need for this include new headlights from 1AAuto.com, Phillips screwdriver, and a 7mm and 10mm socket and ratchet with an extension.

You want to first remove these four Phillips screws, and we'll just fast-forward as Don does this. Pull the light out, twist the sockets counterclockwise, and pull them out. Then, you want to twist this socket out of your side marker light, and then repeat the process on the other side.

Next, you want to remove this series of 7mm bolts, and we'll just fast-forward as Don does this. There's one more 7mm bolt right here. Once those are removed, you want to just lift up this tab, pull the grille forward, and there's another one on the other side. There's another clip right in the center. Using a stick or a long screwdriver, you just want to push that tab and then pull out on that center tab. Just to give you a better look at it, it's this tab right here.

Next, you want to remove these four 10mm bolts that secure your headlight, and we'll just fast-forward as Don removes those. Now, to service your bulbs, both of them are the same. You just pull back this tab and pull the harness free, then twist the bulb out. Push the new one in, twist it clockwise to lock it, and then just reconnect your harness. If you're looking to replace the whole assembly, you just want to disconnect both of these harnesses by pulling up that tab.

Then take your new headlight and push the harnesses into place. Then push your headlight back into place and replace those four 10mm bolts. Once those are in place, take your grille and pull your parking light sockets through, and then you want to line up the tabs on the grille.

The first one you want to do is the center one, and just push down that tab and push the tab on the grilled into place until it locks. Now, line up those side ones and push those into place and we'll just fast-forward here as Don replaces those five 7mm bolts. There's four along the top of the grille, and then that one in the center just above the badge.

Now, twist your side marker light back into place. Then twist your two parking light sockets back into place, just turning them clockwise to lock them. Then push the assembly into place and replace those four Philip screws. Repeat the process on the other side.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Hi, I'm Mike from 1AAuto. We've been selling auto parts for over 30 years! We're dedicated to delivering quality auto parts, expert customer service, and fast and free shipping, all backed by our 100% satisfaction guarantee. So visit us at 1AAuto.com, your trusted source for quality auto parts.

In this video, we're going to be working with our 1996 GMC Sierra. We're going to show you how to remove and replace your vehicle's turn signals. If you like this video, please click subscribe. We have a ton more information on this and many other vehicles. And if you need these parts for your truck, you can follow the link down in the description over to 1AAuto.com.

Here are the items you'll need for this repair.

Remove the four Phillips head screws on the outside edges of your turn signal. We'll do this using a Phillips screwdriver. Once the screws are out, you can pull the housing forward. Remove the electrical connectors. Repeat these steps on the opposite side.

Here we have our turn signals that were removed from our vehicle, and our parts from 1AAuto.com. As you can see, these parts are exactly the same, with the same housings and lenses. Back side has the same openings at the bulb sockets. And we have the same four bulb mounting location. You could see the old ones really fogged up. They're not going to let a lot of light through. They don't look good. These new parts are nice and clear, nice and bright. They're going to get that light through so other people can see what you're doing and update the front of your truck. They'll go in direct fit, just like your original equipment and fix you up right.

Reinstall the lights into the turn signals. Install them into the grill, along with the four Phillips head screws. Repeat these steps on the opposite side.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

We're going to remove the four mounting screws for this lens assembly right here. Slide this out of the way. Now, we're going to remove the mounting bolts that hold on this whole plastic grille assembly here. All right. So, there should be one. Should be one here. All right. Now that we have those bolts out, let's go ahead and give this a little tug. This gives us plenty of space. Now, if you were to look right here, you can see one of the mounting bolts. You can see another one right over here. And then if you were to come right down through here, you're going to find another one and another one. Remove all four of those. We'll get the headlamp loose. Then we'll remove the wiring that goes to the bulbs.

All right. At this point, we can move this around quite a bit. Get these right out of here, sockets. Carefully set that down. Do the same thing here. See if I can get this one out. For this one, it's going to be much easier just to get the wiring off first, and then you'll be able to turn the bulb to be able to remove it. Take a look at that bulb. If you need to replace it, now's a great time. See if we can weasel this out of here now. There it is, friends.

Now, if you look at the top of your headlamp assembly, you're going to notice this adjustment right here. This is to make your lamp assembly go left and right. And this one right here is to make your lamp assembly aim up or down. Just keep that in mind.

So, now's a great time to go ahead and install your bulbs. If you wanted to get some new ones, perfect. Gonna take this, wan to to carefully try to work it so it goes inside here. Fall right in. Okay. So, now, I'm just gonna rest it like this. I'm going to reconnect in my wiring. this one. Come on. Try to grab it here. All right. So, you've got a longer wire and a shorter one. The shorter one's obviously going to go to the closer area. Something that's important to pay attention to is the wiring goes behind this bracket right here. You don't want to put it on the other side because it'll get crushed when you go to mount this in. The other wire, same thing. Behind, that looks great. Now, we're going to put this up against the body. We're going to line up those bolt holes and then we'll start in all of our bolts before we tighten any of them down.

All right. So, now's a perfect time to align those headlights. The reason for that is because the alignment points, like I said, are located right here. And if this is in the way, well, you're not gonna be able to get to them. It's time to get these bolts back in. I'm just going to start it in. We'll start them all in and then we'll snug them up.

All right. Let's tighten them all up. That one didn't hold very well. We'll line it up. Oh yeah, that looks great. Let's get our screws in. Okay. Now, I'm just gonna snug them up. Beautiful.

This is going to be a general tutorial on how to aim your brand new TRQ headlamp assemblies. Okay. So, looking at your brand new TRQ headlamp assembly, you're going to see where your low beam is, and you'll see a little dot right in the center. And that is the access point, okay? So, what we're going to do is we're going to mark that with an erasable marker just so it's easier to see. Next, what we need to do is measure from the level ground up to this point and take note of that measurement. Now, we're just going to pull the car up to our wall. On our vehicle, we remember that the measurement was 28 inches for our access point. Your vehicle may be different, but that's where I'm going to put this tape. Just above that 28 inches. We'll do same on the other side. Okay. So, let's just back the vehicle up straight back 25 feet from the wall. And now that we moved our vehicle 25 feet back from the wall, we're going to start with our measurement here. That's where the headlamp center is. We're gonna go down 4 inches on the driver side.

On the passenger side, we have our line here. What we need to do is go down 2 inches. To adjust the driver side, we're going to cover our passenger side headlamp. If you look at the backside of your headlamp assembly, you're going to see something that looks like this. This is the adjustment. Some of these headlight assemblies have one, two, or even more of them, but you should at least have one. This is how we're going to adjust the headlight beam. Now, we're going to lower the top part of the beam down to just below this line. When you turn the adjustment to the right, it brings the beam up. And if you turn it to the left, it'll bring the headlight beam down. And this is this way on most vehicles. Let's continue on to doing the passenger side. All right. We properly aligned our TRQ headlamp assemblies.

Okay. And on the quality TRQ headlamps for a pickup truck, the procedure is going to be the same. You're going to find your center dot, mark it, and then you'll measure from the level ground up to your dot. So, once your headlamps are properly adjusted, it'll be time to adjust your fog lamps. You'll notice on the driver side, the focal point is all the way at the bottom right now. I would like to bring it up so it meets up with approximately the bottom of the focal point of the headlight. Some fog lamps have an adjuster, others don't. The ones that do have an adjuster, you would just turn the adjustment to the left or to the right to adjust the beam up and down to where it needs to be. Now, with your TRQ headlamps and fog lamps properly aligned, you can drive down the road safely.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to service the headlight bulbs as well as replace the entire headlight assembly on this 1996 Chevy Tahoe. We show you on the passenger side, but the driver side is the same procedure. The items you'll need for this include new headlights from 1AAuto.com, Phillips screwdriver, and a 7mm and 10mm socket and ratchet with an extension.

You want to first remove these four Phillips screws, and we'll just fast-forward as Don does this. Pull the light out, twist the sockets counterclockwise, and pull them out. Then, you want to twist this socket out of your side marker light, and then repeat the process on the other side.

Next, you want to remove this series of 7mm bolts, and we'll just fast-forward as Don does this. There's one more 7mm bolt right here. Once those are removed, you want to just lift up this tab, pull the grille forward, and there's another one on the other side. There's another clip right in the center. Using a stick or a long screwdriver, you just want to push that tab and then pull out on that center tab. Just to give you a better look at it, it's this tab right here.

Next, you want to remove these four 10mm bolts that secure your headlight, and we'll just fast-forward as Don removes those. Now, to service your bulbs, both of them are the same. You just pull back this tab and pull the harness free, then twist the bulb out. Push the new one in, twist it clockwise to lock it, and then just reconnect your harness. If you're looking to replace the whole assembly, you just want to disconnect both of these harnesses by pulling up that tab.

Then take your new headlight and push the harnesses into place. Then push your headlight back into place and replace those four 10mm bolts. Once those are in place, take your grille and pull your parking light sockets through, and then you want to line up the tabs on the grille.

The first one you want to do is the center one, and just push down that tab and push the tab on the grilled into place until it locks. Now, line up those side ones and push those into place and we'll just fast-forward here as Don replaces those five 7mm bolts. There's four along the top of the grille, and then that one in the center just above the badge.

Now, twist your side marker light back into place. Then twist your two parking light sockets back into place, just turning them clockwise to lock them. Then push the assembly into place and replace those four Philip screws. Repeat the process on the other side.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the grille on this 1996 Chevy Tahoe. It's the same part and process on these Tahoes from '95 to 2000. The items you'll need for this are a new grille from 1AAuto.com, Phillips screwdriver, 7mm and 13mm socket and ratchet with an extension, and flat blade screwdriver.

You want to first remove these four Phillips screws. We'll just fast forward as Don does this. Pull the light out and twist these sockets counterclockwise and pull them out. Then you want to twist this socket out of your side marker light. Then repeat the process on the other side.

Next, you want to remove this series of 7mm bolts. We'll just fast forward as Don does this. There's one more 7mm bolt right here. Once those are removed, you want to just lift up this tab and pull the grille forward and there's another one on the other side. There's another clip right in the center, using a stick or a long screwdriver, you just want to push that tab and then pull out on that center tab. Just to give you a better look at it, it's this tab right here.

Up top, is the old grille; below it, are the two from 1A Auto. In the middle is an exact replacement of the old grille and on the bottom is an all chrome version, which we'll be installing on this truck, but first we have to swap over all the stuff from the old grille. You just want to remove these ten 13mm nuts. We'll just fast forward as Don does this. You also want to swap over these clips and there are eight of them in total, four on one side, and four on the other. To remove them, all you do is push in those four triangular pieces, and it just pops out and if gives you any trouble, you can use a flat blade screwdriver to help push it through. We'll fast forward as Don takes the new grille and starts attaching those side marker reflectors and the side marker lights and replacing those 13mm nuts. For the badge, just push it into the center and, just like with the lights, replace those two 13mm nuts. Now, take those eight clips and just push them into place.

Once those are in place, take your grille and pull your parking light sockets through. Then, you want to line up the tabs on the grille, and the first one you want to do is the center one and just push down that tab and push the tab on the grille into place until it locks. Now, line up those side ones and push those into place. We'll just fast forward here as Don replaces those five 7mm bolts. There's four along the top of the grille and then that one in the center just above the badge.

Now, twist your side marker light back into place and then twist your two parking light sockets back into place, just turning them clockwise to lock them. Then push the assembly into place and replace those four Phillips screws. Just repeat the process on the other side.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

We're going to remove the four mounting screws for this lens assembly right here. Slide this out of the way. Now, we're going to remove the mounting bolts that hold on this whole plastic grille assembly here. All right. So, there should be one. Should be one here. All right. Now that we have those bolts out, let's go ahead and give this a little tug. This gives us plenty of space. Now, if you were to look right here, you can see one of the mounting bolts. You can see another one right over here. And then if you were to come right down through here, you're going to find another one and another one. Remove all four of those. We'll get the headlamp loose. Then we'll remove the wiring that goes to the bulbs.

All right. At this point, we can move this around quite a bit. Get these right out of here, sockets. Carefully set that down. Do the same thing here. See if I can get this one out. For this one, it's going to be much easier just to get the wiring off first, and then you'll be able to turn the bulb to be able to remove it. Take a look at that bulb. If you need to replace it, now's a great time. See if we can weasel this out of here now. There it is, friends.

Now, if you look at the top of your headlamp assembly, you're going to notice this adjustment right here. This is to make your lamp assembly go left and right. And this one right here is to make your lamp assembly aim up or down. Just keep that in mind.

So, now's a great time to go ahead and install your bulbs. If you wanted to get some new ones, perfect. Gonna take this, wan to to carefully try to work it so it goes inside here. Fall right in. Okay. So, now, I'm just gonna rest it like this. I'm going to reconnect in my wiring. this one. Come on. Try to grab it here. All right. So, you've got a longer wire and a shorter one. The shorter one's obviously going to go to the closer area. Something that's important to pay attention to is the wiring goes behind this bracket right here. You don't want to put it on the other side because it'll get crushed when you go to mount this in. The other wire, same thing. Behind, that looks great. Now, we're going to put this up against the body. We're going to line up those bolt holes and then we'll start in all of our bolts before we tighten any of them down.

All right. So, now's a perfect time to align those headlights. The reason for that is because the alignment points, like I said, are located right here. And if this is in the way, well, you're not gonna be able to get to them. It's time to get these bolts back in. I'm just going to start it in. We'll start them all in and then we'll snug them up.

All right. Let's tighten them all up. That one didn't hold very well. We'll line it up. Oh yeah, that looks great. Let's get our screws in. Okay. Now, I'm just gonna snug them up. Beautiful.

This is going to be a general tutorial on how to aim your brand new TRQ headlamp assemblies. Okay. So, looking at your brand new TRQ headlamp assembly, you're going to see where your low beam is, and you'll see a little dot right in the center. And that is the access point, okay? So, what we're going to do is we're going to mark that with an erasable marker just so it's easier to see. Next, what we need to do is measure from the level ground up to this point and take note of that measurement. Now, we're just going to pull the car up to our wall. On our vehicle, we remember that the measurement was 28 inches for our access point. Your vehicle may be different, but that's where I'm going to put this tape. Just above that 28 inches. We'll do same on the other side. Okay. So, let's just back the vehicle up straight back 25 feet from the wall. And now that we moved our vehicle 25 feet back from the wall, we're going to start with our measurement here. That's where the headlamp center is. We're gonna go down 4 inches on the driver side.

On the passenger side, we have our line here. What we need to do is go down 2 inches. To adjust the driver side, we're going to cover our passenger side headlamp. If you look at the backside of your headlamp assembly, you're going to see something that looks like this. This is the adjustment. Some of these headlight assemblies have one, two, or even more of them, but you should at least have one. This is how we're going to adjust the headlight beam. Now, we're going to lower the top part of the beam down to just below this line. When you turn the adjustment to the right, it brings the beam up. And if you turn it to the left, it'll bring the headlight beam down. And this is this way on most vehicles. Let's continue on to doing the passenger side. All right. We properly aligned our TRQ headlamp assemblies.

Okay. And on the quality TRQ headlamps for a pickup truck, the procedure is going to be the same. You're going to find your center dot, mark it, and then you'll measure from the level ground up to your dot. So, once your headlamps are properly adjusted, it'll be time to adjust your fog lamps. You'll notice on the driver side, the focal point is all the way at the bottom right now. I would like to bring it up so it meets up with approximately the bottom of the focal point of the headlight. Some fog lamps have an adjuster, others don't. The ones that do have an adjuster, you would just turn the adjustment to the left or to the right to adjust the beam up and down to where it needs to be. Now, with your TRQ headlamps and fog lamps properly aligned, you can drive down the road safely.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace as well as service the bulb in a side marker light on this 1996 Chevy Tahoe. We show you in the passenger side, but the driver side is the same procedure. The items you'll need for this include a new side marker light from 1AAuto.com, a Phillips screwdriver and a 13mm socket and ratchet.

Start off by removing these four Phillips screws. We'll just fast-forward as Don does this. Once those removed, pull the light out, and you just twist the sockets counterclockwise to remove them.

Now to service the bulb on your side marker light. You just twist the socket out and the bulb pulls straight out. You push your new one in, and then the socket twist back into the side marker light.

To change the assembly, you want to remove these two 13mm nuts, so just twist out that socket and remove those two nuts. We'll just fast-forward here as Don does this. Once those are removed, the side marker light will pull right out.

On the left is the old side marker light; on the right is the new one from 1A Auto. You can see they're identical, and they'll mount exactly the same.

Push your new side marker light into place and replace those two 13mm nuts. Then twist your socket back into place.

Now take your parking light and twist those two parking light sockets into place by just twisting them clockwise to lock them. Then push your parking light assembly into place. Make sure all four of those holes line up, and replace those four Phillips screws. Then you're all set.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to service as well as replace the entire taillight assembly on this 1996 Chevy Tahoe. We show you on the driver side, but the passenger side is the same procedure. The items you'll need for this include new taillights from 1AAuto.com, a flat blade screwdriver, and a Phillips screwdriver.

Using your flat blade screwdriver, you want to pry out this cap and this cap right here. Now, you want to remove this Phillips screw and this Phillips screw. We'll just fast-forward as Don does that. Now, pull the taillight straight out and then pull back on the tab on this harness and pull it free.

Now, if you want to just service the bulbs, you just remove these two Phillips screws holding on this panel. Now, you just pull the bulb out and then push your new one in. The other two are the exact same way. If your circuit board ever breaks, we do offer exact replacements at 1AAuto.com.

To replace the bulbs, you can just put that circuit board back into place and replace those two Phillips screws. In the back is the original light; in the middle is the new light from 1AAuto. You can see in exact replacement. We also offer kind of a performance style and these styles do change from time to time. This is example of what we were offering when this video is done.

To re-install, plug it back in, put the light in place, and line up the holes, and re-install those two screws.

Replace those two caps. To give you a better idea of how they look, on the left is the new one and on the right is the old one. You can see they're identical. These just look a little bit newer. Then for the performance taillight and just a close up of it. And you're all set.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the grille on this 1996 Chevy Tahoe. It's the same part and process on these Tahoes from '95 to 2000. The items you'll need for this are a new grille from 1AAuto.com, Phillips screwdriver, 7mm and 13mm socket and ratchet with an extension, and flat blade screwdriver.

You want to first remove these four Phillips screws. We'll just fast forward as Don does this. Pull the light out and twist these sockets counterclockwise and pull them out. Then you want to twist this socket out of your side marker light. Then repeat the process on the other side.

Next, you want to remove this series of 7mm bolts. We'll just fast forward as Don does this. There's one more 7mm bolt right here. Once those are removed, you want to just lift up this tab and pull the grille forward and there's another one on the other side. There's another clip right in the center, using a stick or a long screwdriver, you just want to push that tab and then pull out on that center tab. Just to give you a better look at it, it's this tab right here.

Up top, is the old grille; below it, are the two from 1A Auto. In the middle is an exact replacement of the old grille and on the bottom is an all chrome version, which we'll be installing on this truck, but first we have to swap over all the stuff from the old grille. You just want to remove these ten 13mm nuts. We'll just fast forward as Don does this. You also want to swap over these clips and there are eight of them in total, four on one side, and four on the other. To remove them, all you do is push in those four triangular pieces, and it just pops out and if gives you any trouble, you can use a flat blade screwdriver to help push it through. We'll fast forward as Don takes the new grille and starts attaching those side marker reflectors and the side marker lights and replacing those 13mm nuts. For the badge, just push it into the center and, just like with the lights, replace those two 13mm nuts. Now, take those eight clips and just push them into place.

Once those are in place, take your grille and pull your parking light sockets through. Then, you want to line up the tabs on the grille, and the first one you want to do is the center one and just push down that tab and push the tab on the grille into place until it locks. Now, line up those side ones and push those into place. We'll just fast forward here as Don replaces those five 7mm bolts. There's four along the top of the grille and then that one in the center just above the badge.

Now, twist your side marker light back into place and then twist your two parking light sockets back into place, just turning them clockwise to lock them. Then push the assembly into place and replace those four Phillips screws. Just repeat the process on the other side.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

This video is brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi. I'm Mike Green. In this video, I'm going to show you how to replace the taillights on, this is a 1999 Chevrolet Suburban, but the taillight procedure is the same for this style suburban, Yukon, Tahoe, and also the 88 to 98 Chevrolet and GMC trucks. We'll get to it.

Taillights, once you open the tailgate or the rear doors, are held in by two screws, one down there, and one up in there.
What I have here is a magnet to help me not drop these screws when they come out. If you do end up dropping one, it's just a regular screw. You can get one from the hardware store to replace them.

Now that we have removed the screw, then we can just pull on the light a little bit. There is a gasket around the edge, so it does stick.
Now that the light is separated, you can just reach in and, with your thumb, pull back the tab and pull out the harness. This here is your taillight connector board. Sometimes, if you're taillight's not working, you replace this board, and it will work. Also, if you just want to replace the bulbs, you just remove the two little screws here, pull the board out, and you can replace the bulbs.

With that, now we can reinstall it, hook up the harness, get the tabs to line up, and push it in. Line up your tabs, then put the screws in. What I would suggest for putting the screws back in is put the screw on the screwdriver, very carefully put it in. Same thing with the bottom one, very carefully.

There you have it. Taillight replacement on a 92 to 99 Suburban or 88 to 99 Chevy or GMC truck. Not much more than a Phillips screwdriver, a pen magnet if you have one, and you're set. You can either fix the damaged one, or if your light's not working in your replace the bulbs, and also replace the taillight connecting board.

We hope this helps you out. Check out www.1AAuto.com for all your parts needs. Thank you. This video was brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Call us toll-free 888-844-3393 with any questions. We're the company that's here for you online and here for you in person.