Replaces

1997-2001 Toyota Camry Windshield Washer Reservoir (with Washer Pump) for (US Built Models) Models

This part replaces:

  • OE # 85315AA010
  • Partslink TO1288104
  • Hollander 627-50525

  • New

Our windshield washer reservoirs are some of the highest quality replacements on the market!

This windshield washer bottle with washer pump has been designed to replace the original designs.

Specifications:

  • Brand New Washer Reservoir / Bottle with Washer Pump
  • Direct replacements
  • Replaces dealer part numbers: 85315AA010
  • Plastic construction
  • Includes cap
  • Correct for US Built models only

Now you can buy a high quality windshield washer reservoir that is built to strict quality control standards. REPLACE your broken or cracked one now with this great fitting washer tank.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Bumper Cover (0:37)
    • Remove the two 10mm bolts from the top of the bumper cover
    • Remove the plastic Phillips head clip from the top of the bumper cover
    • Raise and support the vehicle
    • Remove the six 10 millimeter bolts at the bottom of the bumper cover
    • Remove the two plastic Phillips head clips from the bottom of the bumper cover
    • Pull back the inner fenders
    • Remove the 10mm bolt behind each inner fender
    • Pop out the bumper cover retainers
    • Pull the bumper cover off
  2. Removing the Washer Fluid Reservoir (3:31)
    • Remove the two 10mm bolts from the bumper cover
    • Remove the 10mm bolt from the wheel well
    • Fold back the wheel well
    • Have a drain pan ready
    • Disconnect the washer fluid hose
    • Allow the fluid to drain
    • Disconnect the washer pump wiring harness
    • Pop the washer pump out of the retainer
    • Pull the washer pump out of its O-ring
    • Disconnect the fluid level sensor wiring harness
    • Pull the level sensor out of its O-ring
    • Unclip the wiring harness from the fluid reservoir
    • Put the wiring harness aside
    • Unclip the hose from the fluid reservoir
    • Put the hose aside
    • Pull off the Styrofoam bumper if necessary
    • Remove the 10mm nut from the fluid reservoir
    • Remove the two 10mm bolts from the fluid reservoir
    • Pull off the fluid reservoir
  3. Installing the New Washer Fluid Reservoir (7:22)
    • Lift the fluid reservoir into place
    • Hang the reservoir by its stud
    • Start the 10mm nut for the reservoir by hand
    • Start the two 10mm bolts into the reservoir by hand
    • Tighten the nut and two bolts
    • Push the level sensor into its O-ring with the tab facing down
    • Snap the wiring into the retainer
    • Connect the level sensor wiring harness
    • Push the washer pump into its O-ring
    • Snap in the washer pump retainer
    • Connect the washer pump wring harness
    • Clip the hose onto the reservoir
    • Connect the hose to the washer pump
    • Push the wheel well into place
    • Insert the 10mm bolt inside the wheel well
    • Insert the two 10mm bolts into the bottom of the fender liner
  4. Installing the Bumper Cover (9:23)
    • Put the Styrofoam bumper in place, if it has been removed
    • Hold the bumper in place with painter's tape
    • Lift the bumper cover into place
    • Tap in the bumper cover retainers
    • Insert the two 10mm bolts into the top of the bumper cover
    • Insert the plastic clip into the top of the bumper cover
    • Line up the wheel well and bumper screw holes
    • Insert the 10mm bolts into the bottom of the bumper cover
    • Tighten the two plastic clips into the bottom of the bumper cover with a Phillips head screwdriver
    • Insert the two 10mm bolts behind the inner fenders
  5. Filling the Washer Fluid Reservoir (12:32)
    • Lower the vehicle to the ground
    • Remove the strainer from the old fluid reservoir
    • Open the fluid reservoir cap
    • Place the strainer into the new reservoir
    • Add washer fluid to the reservoir

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Drain Pan
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Windshield Washer Fluid

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver
  • No. 2 Phillips Screwdriver

  • Sockets - Metric

  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(13:08 min)

Tools List:

    General Tools

  • Jack Stands
  • Drain Pan
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Windshield Washer Fluid

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver
  • No. 2 Phillips Screwdriver

  • Sockets - Metric

  • 10mm Socket



This part replaces:

  • OE # 85315AA010
  • Partslink TO1288104
  • Hollander 627-50525

Vehicle Fit

  • 1997-2001 Toyota Camry Windshield Washer Reservoir (with Washer Pump) for (US Built Models) Models
$ 47.95
Save 56%
List: $109.12 Save: $61.17
Part #: 1AWWR00018

Out of Stock

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY M-F
For Orders Placed By 5pm Est